Jump to content
SAU Community

Recommended Posts

was intrested in know the first signs of a clutch shitting itself.

the other nite i was at a mates workshop n pulled a nice burnout, but when i changed in second there was major slippage! i took my foot of the accelerator 4 a sec then put it back on n still it was slipping, anyways when i got home it stunk so bad, (not the normal clutch smell) 10x worse.

when driving normally theres no problem, but when i boot it, it feels a lil slower than it should b goin at higher revs,

also when i down gear into 2nd doin round 50km/h i can smell the clutch again.

is my clutch on its way out?

should i start saving 4 another?

or do i still have a while b4 it will need changing?

thanks in advance

john

Link to comment
https://www.sau.com.au/forums/topic/42327-clutch-issues/
Share on other sites

smells like fish when frying the clutch.

You can tell if you drive at like 60k's, put it in 5th gear and floor it. If the revs jump but speed doesn't, then you're in trouble. if not you could be aight for a while.

Also, rev the car up to like 5000-5500 before changing and see if the revs jump up then settle back down. If they do jump up, then its slipping.

Link to comment
https://www.sau.com.au/forums/topic/42327-clutch-issues/#findComment-865211
Share on other sites

Yeah I had the same thing, it felt a little funny on the way to work (~40km), and I almost didn't make it home... It happened as got a near perfect launch the previous day, and burnt the stock clutch from excess slippage on take off. The was still a bit of meat on the clutch, but I had glazed it so bad, there was barely any friction.

My advice is NOT to accelerate hard under any circumstances to prolong it until you have a chance to change it, otherwise your car will soon be undriveable...

Link to comment
https://www.sau.com.au/forums/topic/42327-clutch-issues/#findComment-867428
Share on other sites

mate the same thing happened to me once, what i think you have done is glazed the surface of your clutch...u might still have a fair bit on it but you will need to change it sooner or later... Soon after that happened in the mornings the clutch would shudder a bit untill it warmed up, you will have a month or so of use, but it will start pissing you off soon so an exedy single plate is a good idea...

Link to comment
https://www.sau.com.au/forums/topic/42327-clutch-issues/#findComment-874395
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • That's not a transistor --- it's marked ZD1 which makes it a zener diode. As to what the breakdown voltage is, not enough there to divine.
    • Hi all, Long time since I've posted here. Looking for some advice on what I can remove to further identify the cause of my issues.  I can move the passenger seat forward and back but the knob used to adjust the seat angle is pretty much free spinning, there's very little resistance.  Removing the side cover I can see that the chain is intact but the shaft for the adjustment spins without the gear attached to it moving.  What's my next step for disassembly here? Is this a common fault? Just being a little cautious as I didn't want to start removing bolts for a spring to fly out or something equally as stupid.  Cheers
    • The incentives are mostly the same, yes. Ethanol is cheap compared to the cost of doing 98-100 RON with crude oil alone. 87 to 93-94 AKI all with E10. In 2020 Canada mandated E10 as a part of their "renewable fuel standard" and is supposedly going to go to E15 in 2030. In California where there are only 8 refineries with two threatening to shut down next year it's been over 20 years now of E10 and 91 AKI maximum because there's just not enough refinery capacity or crude oil supply relative to the demand for premium unleaded fuel. And CARB's low carbon fuel standard means functionally none of the diesel available at the pump is made from crude oil anymore. It's almost all entirely 20% biodiesel blended with 80% renewable diesel (hydrotreated vegetable oil) now. The number of gasoline vehicles that support E15 or higher ethanol concentrations is surprisingly low, I can't imagine it being wise to play tricks like this without flex fuel sensors in most of the fleet.
    • It's almost certainly the same as the one next to it. Have a fish around amongst these hits https://www.google.com/search?q=surface+mount+transistor+m33&sca_esv=9cb49794e0b2005d&source=hp&ei=2vJ5aNjTB7Kw0PEPldnS8QM&iflsig=AOw8s4IAAAAAaHoA6qkfmF6XcygtrZ4Vu9f92NXF_RFd&ved=0ahUKEwjYqIPP7MWOAxUyGDQIHZWsND4Q4dUDCA8&uact=5&oq=surface+mount+transistor+m33&gs_lp=Egdnd3Mtd2l6IhxzdXJmYWNlIG1vdW50IHRyYW5zaXN0b3IgbTMzMgUQIRigATIFECEYoAEyBRAhGKABMgUQIRigAUjKCFAAWABwAHgAkAEAmAHfAaAB3wGqAQMyLTG4AQPIAQD4AQL4AQGYAgGgAuYBmAMAkgcDMi0xoAfMBLIHAzItMbgH5gHCBwMyLTHIBwU&sclient=gws-wiz
    • South Australia, which is hardly as far behind as the rest pf Oz makes out, and who is also not a paragon of progressiveness (read that as over-legislation) in the area of vehicle standards, has this to say on the subject: Adjustable coil-over suspension Aftermarket adjustable coil-over suspension components are suspension units that incorporate an external thread on the main body and corresponding threaded spring saddle that allows the vehicle's suspension height to be varied. If fitting aftermarket or coil-over suspension components you must submit an Application to modify a light motor vehicle form and a report from a light vehicle engineering signatory (LVES).
×
×
  • Create New...