Jump to content
SAU Community

Recommended Posts

was intrested in know the first signs of a clutch shitting itself.

the other nite i was at a mates workshop n pulled a nice burnout, but when i changed in second there was major slippage! i took my foot of the accelerator 4 a sec then put it back on n still it was slipping, anyways when i got home it stunk so bad, (not the normal clutch smell) 10x worse.

when driving normally theres no problem, but when i boot it, it feels a lil slower than it should b goin at higher revs,

also when i down gear into 2nd doin round 50km/h i can smell the clutch again.

is my clutch on its way out?

should i start saving 4 another?

or do i still have a while b4 it will need changing?

thanks in advance

john

Link to comment
https://www.sau.com.au/forums/topic/42327-clutch-issues/
Share on other sites

smells like fish when frying the clutch.

You can tell if you drive at like 60k's, put it in 5th gear and floor it. If the revs jump but speed doesn't, then you're in trouble. if not you could be aight for a while.

Also, rev the car up to like 5000-5500 before changing and see if the revs jump up then settle back down. If they do jump up, then its slipping.

Link to comment
https://www.sau.com.au/forums/topic/42327-clutch-issues/#findComment-865211
Share on other sites

Yeah I had the same thing, it felt a little funny on the way to work (~40km), and I almost didn't make it home... It happened as got a near perfect launch the previous day, and burnt the stock clutch from excess slippage on take off. The was still a bit of meat on the clutch, but I had glazed it so bad, there was barely any friction.

My advice is NOT to accelerate hard under any circumstances to prolong it until you have a chance to change it, otherwise your car will soon be undriveable...

Link to comment
https://www.sau.com.au/forums/topic/42327-clutch-issues/#findComment-867428
Share on other sites

mate the same thing happened to me once, what i think you have done is glazed the surface of your clutch...u might still have a fair bit on it but you will need to change it sooner or later... Soon after that happened in the mornings the clutch would shudder a bit untill it warmed up, you will have a month or so of use, but it will start pissing you off soon so an exedy single plate is a good idea...

Link to comment
https://www.sau.com.au/forums/topic/42327-clutch-issues/#findComment-874395
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...