Jump to content
SAU Community

FK, urgent advice required

Jolinator

By Jolinator,
in General Maintenance

 Share

Recommended Posts

Jolinator Proficient

Jolinator

Posted
Posted

got my car up on axle stands as i speak, doing a general service, i have a oil leak coming from my gearbox

on the car looking from the back, the fill plug on the gearbox is on the left, on the opposite side there is a sensor the sensor its self is leaking fluid, im just wondering what sensor it is as i need to order a replacement:(

Link to comment
https://www.sau.com.au/forums/topic/42334-fk-urgent-advice-required/
Share on other sites
Danzil Enthusiast

Danzil

Posted
Posted

Yeah same thing happened to me

Overfilled my box and after driving it looked like it was leaking from the side sensor. Took it to a mechanic and he told me it was the bleeder from the top of the box letting out excess fluid...sometimes it takes a while to rid of all the fluid from the bleeder and when you wipe it it might come out some more after a while.

Best to get it checked out anyways.

-Dan

Danzil Enthusiast

Danzil

Posted
Posted

Yeah as said b4 might be overfilled and its coming out the bleeder. When you drive the oil gets blown down and may look like its coming out of the sensor. The bleeder is situated at the top of the box. It may also take a while for all the oil to come out, so if you wipe it once after a while it may appear again.

Same thing happend to me and thats what the mechaic told me...but to be sure get it checked out anyways.

-Dan

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • sonicii
      Could it really happen......

      By sonicii · Posted

      I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • MBS206
      Could it really happen......

      By MBS206 · Posted

      Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • MBS206
      R34 25GT Engine Light 21

      By MBS206 · Posted

      Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
×
×
  • Create New...