Jump to content
SAU Community

Recommended Posts

Hi all, For sale is my V35 sedan, Details are as follows, This is a Genuine sale, I have a new car.

Asking price is $16,000 but I am open to negotiation.

I am the 1st Aus owner, Low Km's, Tasteful Mods, Regular services, mature owner.
Roadworthy is done, QLD Rego till September - She is ready to go!! :)
This car is reliable and such a pleasure to drive, plenty of power and handles lovely with the Tein suspension and slotted front rotors. The Agency power exhaust has an amazing note whilst not attracting unwanted attention. Driving at night is a dream with the projector headlights and 50W Hid's with secondary 35W Hid's and Angel eyes.
Original exhaust and suspension can be supplied if required.
Mods:
3” stainless exhaust Y-pipe back
MACE 8mm Plenum spacer (First one in Aus)
NGK platinum plugs
K&N Panel filter
350z intake pipe
Alpine Mp3/ipod Head unit
Focal splits
Type S 12" in fibreglass molded box
Custom projector headlights FX-R 2.0
Stillen Engine damper
Strut brace
Tein Control master coilovers
Dark tint
Carbon fibre look engine cover


Features:
6 speed manual
3.5litre
Battery year old
18” mags
A/C, Pwr Steer/PWR windows/VDC/ABS
Aus standards immobiliser
Paint in good condition (few marks)
700kms per tank
No oil/ coolant leaks
No running problems
No interior damage/rips/scratches
New windscreen
****PERSONALISED NUMBER PLATES DO NOT COME WITH THIS SALE*** Standard issue plates are attached to this vehicle already

Car is located in Brisbane Bayside can be viewed on weekends or by appointment. Call Samantha, anytime on 0402699119 or email [email protected] Thanks for looking.

post-82567-0-31765700-1365758843_thumb.jpg

post-82567-0-58884300-1365758855_thumb.jpg

post-82567-0-10122200-1365758867_thumb.jpg

post-82567-0-37207100-1365758880_thumb.jpg

post-82567-0-48831800-1365758896_thumb.jpg

post-82567-0-43469000-1365758912_thumb.jpg

post-82567-0-47423900-1365758926_thumb.jpg

post-82567-0-37482200-1365758943_thumb.jpg

post-82567-0-54363600-1365758953_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/423424-2004-v35-sedan-manual/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You don't need to drain the intake heat exchanger to remove the radiator but depending on your plans you may need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
    • LOL, all of the CAI like Craig I just need to put a hole saw through my bumper Done and dusted, the car runs, which is nice, I'll take it for a spin when the weather clears up Just need to put the bumper back on for good
    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
×
×
  • Create New...