Jump to content
SAU Community

Recommended Posts

Shit man, 10 sec GTS-T for 10K is stupid easy and your putting way too much into your budget.

find 400+ meter high cliff,

Push car off

ignoring drag this should get you a 9.03 second 400 meter

Collect insurance,

blow and hookers all round.

You sir.................. Are a genius!

Shit man, 10 sec GTS-T for 10K is stupid easy and your putting way too much into your budget.

find 400+ meter high cliff,

Push car off

ignoring drag this should get you a 9.03 second 400 meter

Collect insurance,

blow and hookers all round.

clap-clap-clap-eccbc87e4b5ce2fe28308fd9f

Holset hx52 turbo.

Deatchworks 1000cc s/f injectors.

China intercooler

Hybrid/nz top mount manifold.

NPC/Jim berry clutch.

Welded diff

Adaptronic ecu

Custom 4" side exit exhaust and gate

Precision 66mm gate

Nismo drop in pump

Fully sick shift light

Mickey tees slick

Front runners

Trent from cheuqed tuning for a tune.

Probably left some things out but you get the idea haha. Feel free to tell me what I forgot.

if your serious... and that's a big if.

Your best chance at a good time without alot of seat time or skills is...

You need a drag based auto.... think used c6 or 2 speed glide that has been built for drag with trans brake.

Bellhousing

Converter

Shifter

Drive shaft

Weld diff

Used slicks

Line locker

Stock suspension

Strip EVERYTHING out you don't need for the race.

Obviously then big turbo, fuel system etc.

If you can buy right, a 10sec run for 10k is very doable...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...