Jump to content
SAU Community

Recommended Posts

hi guys iv searched the forums here and around the net and couldn't find anything to help me so hoping someone here can

I have a 1993 r33 gts25t. its stock under the hood besides a fmic, nismo fpr (coz stock one died n couldn't get another one), hks bov and a pod filter

I don't drive it to often so started it in the shed n let it idle to put some charge in the battery. it was running fine then the idle started to fluctuate slightly then it stalled I tried to start it n it turns over but wont fire up.

I have limited mechanical knowledge so I checked all the basic things its got spark its getting fuel all the fuses and relays are fine.

so following info I found on the net of things that could be the problem iv replaced cas, afm and ignitor and still no luck.

any info or suggestions would be greatly appreciated Thanks Heaps

Link to comment
https://www.sau.com.au/forums/topic/426483-r33-wont-start-all-help-appreciated/
Share on other sites

fuel I pulled off the return line n injectors clicked when I rotate the cas and the plugs where wet when I pulled them out and spark I removed the coil packs and plugs one at a time n placed the plug in the coil pack and earthed it to a battery with a jumper cable and had a mate turn the key.

I just read on here that one guy found even though the plugs fired out of the engine they where still to weak to start the car so ill try replacing the plugs tomorrow.

I had a problem like this before an it was the power supply to the coils, It red fine with a volt meter but had no current, to check this get a headlight globe pref. 100w , find the power wire on the coils-remove all the plugs off the coils to confirm the power supply wire see if it glows the bulb bright like a headlight-if not you have found your problem area. Is it the model with the ignitor at rear of engine or do the coils have inbuilt ignitor.I think 93 has the ignitor.

yes it has the ignitor at the rear of the motor atop the coil pack cover

I checked the power supply to the coil packs like u said an it is fine the bulb was blinding lol

this first happened a few months ago but haven't had the time to work on it till now I thought I was getting fuel then but after closer inspection to day it looks like there's fuel in the feed and return line but its not making it to the cylinder coz the plugs are bone dry now after cranking for 5 seconds

discovered iv got no power to the injectors checked all the wires and earths and is all good so and everything else appears fine fuel pressure, spark, injectors them selves. So im thinking its a problem with the ecu.

is this a likely possibility???

if the plugs are wet then the injectors sounds like theyre working.

did u only jist install the fpr? sounds like the pressure is too high and u have fouled the spark plugs.

get some new spark plugs and set the fuel pressure to 43.5psi when the pump primes. then see if it starts

hey plugs where wet when It first happened but are bone dry now

I put new plugs in and the fuel pressure is set at 43.5psi

I spoke to the mechanic at the local Nissan dealership said it sounds like the ecu but when I asked if I could ring it in there he said they not interested in working on it :-(

so I got another ecu do I just unplug the old one n plug in the new one or is there other steps to replacing it ???

If I here ecu one more time I'm gonna burst into laughter, I have seen r33 ecu,s cooking when my mate reversed the polarity to his battery for 2 minutes. There was smoke coming out the engine bay then he swapped it over and it fired right up please accept out information, it is your battery or ignitor unless a magpie got stuck in your alternator and the battery didnt charge properly.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • CTIS (Central Tire Inflation System) has existed since the 80's. I'm looking into buying a Hummer H1 and they generally included it. 
    • My idle is set at 950rpm though - Moving the timing around 20 degrees is not really what I'd call a calm idle. That said... neither is chop, by definition. The LS ECU likes to adjust timing to hold idle as opposed to air. It'd work, but generally speaking there'd be a discrepancy in the base idle and the IACV would want to move the timing around anyway to maintain said idle. I think I'm just going to keep the timing steady anyway. Preserve my engine mounts.  My aircon is now officially regassed. As the guy was reversing I noticed my reverse lights do not operate, along with my reverse cam. This is a bit distressing, because 100% of guides talk about which wire to connect to backup cams as "the goes with the [other color] wire". Often when doing conversions. Unfortunately the R34 colour wires aren't documented Unfortunately I had a T56 Magnum gearbox with it's reverse switch, which also isn't documented. Unfortunately there's definitely not documentation for people with both of these in the one car. Unfortunately I forgot. After many hours of this, I have a reverse cam and reverse lights again. The wire going through the trans tunnel to the reverse switch had broken. Upon inspection, it looks like this one wire had about 7 spade terminals and extensions in it.. for reasons I cannot possibly comprehend. I also spent the 750 hours required to clean up the wiring behind my head unit which now looks like this: This is a monumental improvement relative to what used to be there WRT triple gauges, head unit, traction control, wideband controller, and whatever the f**k OEM stuff still exists there in various states of connectivity/needed. Next step is to check in at the Exhaust shop to see/confirm how much clearance I have, to decide what mid mufflers or 'resonators' (which are just straight through, narrower mufflers) I can add and hopefully cut out a lot of exhaust leaks, pinhole, v-band or otherwise. But first step will be to 'take a look' before the next step.
    • Fark the AFM card and Nistune, Haltech Nexus S3, DBW, cruise control, flex fuel, dis dat.  
    • It's most likely the bolt/bush where the cover bolts back wore and allowed cover to move forward.
    • Still haven't put the injectors and R35 AFM in so we can tune the bloody thing for the HG highflow it got mid last year! I think I can forecast the upgrade path to a bigger twin scroll, external gate, Haltech, flex setup, Samsonas, dis dat, etc will be .... a while away!
×
×
  • Create New...