Jump to content
SAU Community

Recommended Posts

SERIES 1 PARTS

All my aftermarket parts are listed separately

Rb25det block

$50

R33 s1 headlights great condition

Has one broken clip for the grill

Chrome backing very rare

$200 pair

R33 complete boot trim

$70

r33 gtst front hubs

$50 pair

Rear reo

$30

Radiator support great condition

$50

r33 gtst brake master complete non abs

great condition

$30

r33 engine crossmember perfect for rb conversions

$50

R33 power steer rack

Great condition

$30

r33 front sway bar

$10

r33 series 1 behind the dash aircon stuff

make a offer

r33 series 1 window trims from door and car the one that always fade

make a offer

r33 overflow bottle

$10

R33 gtst ignition barrel and locks with key

Good condition

$130

R33 gtst side mirrors

$20 each

r33 passenger side gaurd with blinker

maroon and white

$20

R33 drivers side Gaurd with blinker

White

$20

R33 series 1 bonnet

White needs paint not best of nick

$50

Series 1 front reo

$60

R33 Gtr look alike front bar

Needs slight repair

$50

R33 series 1 dash

$30

R33 gtst centre console

Good condition

$20

R33 doors bare

good condition

$20 each

R33 gtst tail lights

Great condition

$20 each

R33 glovebox

$20

R33 boot with aftermarket wing/spoiler looks similiar to standard one lights up skyline

$20

R33 boot with o wing but holes

White

$20

R33 handbrake with full handbrake cable to hubs

$30

R33 passenger window reg motor

$20

R33 passenger window switch

$20

R33 bonnet latch and cable

$30

R33 bonnet latch bracket

$20

r33 boot and fuel flap latch assembly

$20

r33 air con unit/display

$20

R33 rear bar maroon, silver and white

$30

R33 complete air con set up with everything!

condenser

compressor

dryer

lines etc

$130

R33 rear seats

$30

SERIES 2 PARTS

R33 series 2 dash complete in good condition

$80

R33 genuine gtr grill

White bit rough needs to be fixed up

$40

R33 series 2 headlight

One broken clip for grill

$50

r33 gtst front hubs

$50

r33 gtst series 2 brake master complete abs

great condition

$50

R33 clutch master cylinder

$60

r33 engine crossmember perfect for rb conversions

$50

R33 series 2 power steer rack

Great condition

$30

r33 front sway bar

$10

r33 series 2 behind the dash aircon stuff

make a offer

r33 series 2 window trims from door and car the one that always fade

make a 0ffer

r33 overflow bottle

$15

R33 washer bottle

$30

R33 standard shocks and springs

$40

r33 gtst series 2 front seats

Great condition drivers have minor tear

$50

r33 series 2 rear bar silver

$40

R33 gtst series 2 ignition barrel and locks with key

Good condition

$130

R33 gtst series 2 side mirror passenger silver

$30

r33 passenger side gaurd with blinker

Silver

$30

R33 gtst series 2 centre console

Good condition

$20

R33 series 2 door passenger

good condition

$20

R33 gtst tail lights

Great condition

$30 each

R33 glovebox

$20

R33 handbrake with full handbrake cable to hubs

$50

R33 pasenger window reg motor

$35

R33 drivers side window reg and motor

$40

R33 passenger window switch

$20

R33 bonnet latch and cable

$50

R33 bonnet latch bracket

$40

r33 boot and fuel flap latch assembly

$30

r33 series 2 air con unit/display

$30

R33 series 2 steering wheel with air bag

Make a offer

R33 series 2 complete air con set up with everything!

$150

i have all the interior plastics etc

So much more just can't think text me or pm me if you need anything

Gold Coast can post

0487924497

Link to comment
https://www.sau.com.au/forums/topic/426904-parting-r33-gtst-qld-can-post/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...