Jump to content
SAU Community

Window Seal/motor/regulator

Xtaoi

By Xtaoi,
in General Maintenance

 Share

Recommended Posts

Xtaoi Enthusiast

Xtaoi

Posted
Posted

Recently my seal on my 1998 R34 GT-T's passenger side window (2 door) has started to play up. It is starting to fall off. It doesn't look in generally bad condition.. is it worth replacing the seal or just buying some special adhesive and sticking it back on? Also, the window itself when I go to wind it down.. the back part of the window doesn't wind down.. i have to help push it down.. is this due to a motor failure on the window? or maybe not on the rails correctly? Seems like a stupid question but im just trying to see how much money i can save rather than taking it somewhere and have them charge me too much :P

Link to comment
https://www.sau.com.au/forums/topic/427200-window-sealmotorregulator/
Share on other sites
darksky34 Mentor

darksky34

Posted
Posted

for the window winding part, try to take the door apart to see if the window isn't sitting on the rail properly, you might find it's a different problem (motor failure etc) then you can buy parts and put it back in yourself.

  • 6 months later...
  • 5 months later...
mistermeena Enthusiast

mistermeena

Posted
Posted

do you mean the rubber part is coming away from the backing strip (the u-shaped hard bit)? if so just glue it back on with some adhesive silicone if it's just a small area. If it's heaps of it then reattaching it is a pain so go to clarke rubber and match it with what they've got. It's called pinchweld.

Lolrick Collaborator

Lolrick

Posted
Posted

Hey, basically door seals aren't glued in, they just use suction - I had a mate at work put mine back in fairly snugly, took him 5 seconds!

As for the window, it was a broken bush on the window regulator causing the back part to stay down. I purchased and fitted a new passenger regulator, but after hours of jigging around i couldn't quite get it to come up flush with the seals - it works and stays straight, but sometimes it digs into the seals. Something ill have to live with!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Murray_Calavera
      "Cheap" bolt on turbo on RB25DET NEO

      By Murray_Calavera · Posted

      The fab work can be as simple as a couple of silicon hoses and clamps to the factory piping. 
    • joshuaho96
      "Cheap" bolt on turbo on RB25DET NEO

      By joshuaho96 · Posted

      Just sounds like either way you need to do some fab work to get everything to fit, so why limit yourself at that point? If the GCG high flow option is zero effort in and out swap though I'd probably do that. It's almost certainly lowest risk, lowest cost, etc. The HKS GTIII-RS option that Kapr mentioned is laughably expensive for what it is, they charge the exact same for two turbos on the RB26 so their margins are off the charts on that thing.
    • GTSBoy
      "Cheap" bolt on turbo on RB25DET NEO

      By GTSBoy · Posted

      Intake manifold is not a part of the issue. The turbo bolts to the exhaust manifold. That is easy. But close your eyes and picture the physical situation. That is a T3 flange on the manifold and a T3 flange on the turbo. As long as any new turbo has a T3 flange on the exhaust housing, that exhaust housing will bolt to the exhaust manifold. This places the exhaust housing in the same place as the stock one. But now move your mental attention a little further forward. The location of the compressor housing is set by the length of the turbo's core. The stock turbo had a long core. Let's say that it is..... 100mm long. So that would place the compressor housing 100mm forward of the exhaust housing. But a highflow, might well have a centre core that is shorter. Let's say that it is only 70mm long. Now the compressor housing will be 30mm further back in the engine bay than the stock one. This DOES move the turbo's compressor outlet backwards. It also moves the compressor's inlet backwards. You will very likely have to do some work to both the inlet and outlet piping to make everything connect again. I am not say this to make it out to be a bigger deal than it is. I am just pointing out that "bolt on" is sometimes not quite bolt on. The highflow from GCG that Murray linked above (https://gcg.com.au/turbo-charger-upgrade-skyline-gtst-2iu-xtrgts-s1.html ) uses a core that is the same length as the stock core, and so does not require this extra work. It will look very much like the stock turbo. No-one uses GTR turbos of any flavour (stock, or aftermarket) in a single turbo application on RB20/25. It's not a thing. Yes, people have been putting on GT3076, GTX3076 (and bigger and smaller versions of those) and G30s (of various sizes) onto RB20/25 since forever. But these are not "bolt on". Everything except the 4 bolts to the exhaust manifold change with these. And genuine Garretts are expensive. Non-gen, like Pulsar, etc, are cheaper, variously as good or nearly as good. But still not bolt on. No-one in the right mind would pay for an HKS turbo. Not in this modern day and age. Well, yes, the GCG highflow. You could ask HG what he can do to make the compressor housing sit in the original location. There are surely others doing highflows around the world. And some of the eBay/Temu ones (as reported by Dose) work and don't die. Bit of a lottery though. I would send your turbo to GCG (here in Oz) to be highflowed if you want a trivial no-extra-work option. But seriously, the work required to change inlet and outlet piping is not that hard. That's a boost control problem, not a turbo problem.
    • Kapr
      "Cheap" bolt on turbo on RB25DET NEO

      By Kapr · Posted

      Thank you all for the replys 🙂 I know that intake would be different but that is one pipe at it is not that hard to get(custom one). I meant mainly bolt to the stock manifold and the turbo elbow. I looked and many sites/forums but they are just "old" with some old HKS turbos from GT-R i guess? What about some Garrets?  Or any other turbo? Is there even a turbo which i can just bolt on? 😄 And yeah i know about that new HKS but that is like 2000k USD without taxes/shipping in here   Iam getting a touch up tune but my "problem" is that on the "not" hot day iam getting peaks around 0,9 bar...and when it was around 15 Celsious i saw peak around 1 bar which is just too much for stock turbo. And of course turbo is old and i like to get some new one for a piece of mind 🙂 
    • GTSBoy
      new here

      By GTSBoy · Posted

      I'm working on the assumption that our friend Jasmine here is a Russian (or, possibly Ukrainian) spammer/spambot, based purely on the number of such that I have been having to neuter in the last few weeks. IP address for the OP above was in WA. But that could have been via VPN. Posting at quarter to 4 in the morning is a good sign of being from somewhere in Europe. The last Jasmine that I kicked in the cooch was IP addressed in Ukraine. Even that could have been via VPN, and the bitchbot could have been from Russia, Serbia, China or anywhere. Regardless, was a spambot, so I killed it with fire. The fact that our new friend Jasmine here did not respond in any way to my tart query strongly suggests to me that this OP was just the establishment phase of a user able to be activated for spamming in a week, or 3 or 10.
×
×
  • Create New...