Jump to content
SAU Community

Rb25 Fuel Rail Ebay Spec. Which Fpr To Mount To Fuel Rail?

jamesdt

By jamesdt,
in Engines & Forced Induction

 Share

Recommended Posts

jamesdt Enthusiast

jamesdt

Posted
Posted

Need to get a top feed fuel for my rb25. Are the cheap ebay fuel rails any good or are they just rubbish? Pretty much need a rail and injectors that will clear my plazmaman plenum. Also which fuel pressure reg will I be best off using. I'd like to use something that can be mounted directly to the end rail if possible.

Injectors will need to support e85, running a gtx3076 turbo so will id1000's be best off or id2000's be to over kill? Or is there another top feed injector that's just as good as id's?

Thanks guys.

Aldawy Explorer

Aldawy

Posted
Posted

On eBay there was one that I seen, it was black , can't remember the name.

It had threaded ends for twin feed and return was in the middle on the bottom not the top. Top return hits all standard manifolds (were the middle bolt is for the pleanm would hit the return if it was on the top)

It also came in kits with Id injectors (1000 / 2000) and turbo smart fuel reg

They also sold it on its own ,injector size was 11mm and 14mm

I'll get a picture for you so you know witch one to look for

  • 2 weeks later...
34GeeTeeTee Grand Master

34GeeTeeTee

Posted
Posted

Need to get a top feed fuel for my rb25. Are the cheap ebay fuel rails any good or are they just rubbish? Pretty much need a rail and injectors that will clear my plazmaman plenum. Also which fuel pressure reg will I be best off using. I'd like to use something that can be mounted directly to the end rail if possible.

Injectors will need to support e85, running a gtx3076 turbo so will id1000's be best off or id2000's be to over kill? Or is there another top feed injector that's just as good as id's?

Thanks guys.

Get a plazmaman rail to match the plenum?

As for injectors, 1000's will get you to the turbo limit no problem so they will be fine! 2000's will also work!

I have a brand new black anodised proflow one here you could have cheap...

Ooh or do this!

jamesdt Enthusiast

jamesdt

Posted
  • Author
Posted

was just seeing if there was a cheaper alternative than the plazmaman rail that would still work perfectly well, i noticed in another thread some one had said these work. does any one know forsure??

http://goodiesdirect.com.au/index.php?route=product/product&path=81_88_90&product_id=405

i guess the only issue there is that there 11mm fuel rails so if i go and buy a set of id1000's with 11mm tops, if it doesnt end up fitting with this fuel rail and i have to go and buy a plazmaman fuel rail which is 14mm i dont think id be able to run the top hat adaptors on the injectors to convert to 14mm because of clearance issues

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Matt Z
      SAU NSW - Archies Flame Grille Meet & Cruise to Kurnell

      By Matt Z · Posted

      Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
    • Ozdavroz
      WTAC 2025

      By Ozdavroz · Posted

      Yeah good luck out there! Will be good to see a mighty GTST going harder than the GTRs
    • bcozican
      WTAC 2025

      By bcozican · Posted

      i will be there 😁
    • patrickxdf12
      Squeaking clutch/throw out bearing

      By patrickxdf12 · Posted

      Hello!  i just finished manual swaping my r34 skyline with a r33 rb20de box(RB71C)box  When the car is running it squeaks crazy loud and it was smoking from the gearbox area. The gearbox is fine it was tested. The clutch slave cylinder seems like it doesn't fully releases the clutch. I want to ask if this noise is from the throw out bearing or could it be the clutch assembly or disk att.xFliq87Gzw6kImKBVqDebXkj0fBqymk0JaYeP3_3SlM.mp4
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
×
×
  • Create New...