Jump to content
SAU Community

Recommended Posts

I bought my car in May 2012. I was very impressed by the fact the car had all original paint and panels (with panel gaps that were 100% factory). However, the paint was not in the best condition....and I always thought my car looked a tad dull compared to other examples I've seen in real life and on the internet.

It is now in July 2013, that I have finally gotten around to restoring the car back to its former glory, sort of. The reason I say sort of is because the front bumper is pelted with rock chips, the rear bar is a scratched through the clear coat, and the bonnet has a fair few stone chips which would require a lot of brush touching.

Now, I drive this car on a daily basis. I strongly believe that a performance car is built to be driven, and also kept looking nice. I think it is a bit of a shame when performance cars rarely ever come out of the garage.

I believe you develop a better bond with your car by appreciating how to tackle all the shapes and curves of the car through detailing. I use a Dual Action Polisher, and with the correct pad and product selection, you CAN achieve the same results as with a Rotary, but with less risk. The only downside is it will take a bit more time.

Here is my album of photographs BEFORE starting the DETAIL.

http://imgur.com/a/lLaNY#0


I put roughly a LOT of man hours into this restoration. I did an extensive amount of prep work before I commenced a 3 stage polishing regimen with an aggressive compound, intermediate polish, and a jewelling polish.

& Here are my results....(the pictures taken are with a sealant applied after polishing, once I apply carnauba wax I will take the car out in sunlight and take more pictures). I haven't applied trim conditioners or anything either yet.

lg4P6Jk.jpg

lg4P6Jk.jpg

Mfm28Yj.jpg

kzvjwjt.jpg

uY87nWp.jpg

luSMWvI.jpg

qyYuA5U.jpg

pT5ezE7.jpgAm6kcAi.jpgXfK9qJT.jpggtOxfVF.jpg

2Rav3js.jpg

WlB1O5n.jpg

ar1kBUC.jpg

4ZPEOM8.jpg

eAMZqHo.jpg

ppMrHG2.jpg

  • Like 1

Would've helped if you noted which photos were which, as it's kind of hard to see the differences before and after detailing. Put them in some sort of order.

Not sure what you mean. The album link is all the before photos. Just a random assortment showing the paint has a lot of scratches, swirls, etching, general contamination etc.

The pictures posted in this thread here are after photos. As you can tell, there is none of that present in the after photos.

Well done mate looking sweet so far. Saw a random bottle of ammo - who stocks the stuff in oz?

Hi, thanks man.

I got my stuff via airmail from Ammo in America. I used AMMO skin to seal the car.

  • 3 weeks later...
  • 4 weeks later...

Well, it's now been close to 2 months since I completed the detail....

I spent some time today washing the car, and then I applied a layer of carnauba wax, let it sit for 45 minutes, then buffed it off by hand with a megs microfiber towel.

These pictures should give you a good idea of how the car looks in natural lighting in the afternoon.

The reflections really have a lot of clarity which I'm super happy about, as I was able to remove a lot of the factory orange peel in the paint when I went through the compounding to polishing phases (this was my one of my goals).

Roof

rdnG2ZJ.jpg

Roof

NrCSzSc.jpg

Hey Benji great job, just thought I'd ask is have you used autoglym super resin polish and hd wax before? You can source the polish via eBay for half the price retailers in aussieland can sell it for and the wax the cheapest I've seen is about $85 but seriously its easy to apply and easy to come off and it makes a fantastic difference

Hey Benji great job, just thought I'd ask is have you used autoglym super resin polish and hd wax before? You can source the polish via eBay for half the price retailers in aussieland can sell it for and the wax the cheapest I've seen is about $85 but seriously its easy to apply and easy to come off and it makes a fantastic difference

Hi Ken,

Cheers!

As for your questions:

Super resin polish - it is lightlyyyy abrasive but its downfall is it contains a lot of fillers. After you polish these fillers will be left to hide swirls or scratches. If you want to remove scratches completely you'd use a different product.

Hd wax - I am not too familiar with the HD wax...but if it is priced at $85 I assume it would be a good carnauba based wax.

I use Dodo juice supernatural carnauba wax (can get it from the UK for an ok price) applied over a base of AMMO NYC sealant (sealant is applied, buffed off with MF towel, left to cure for 24 hrs to bond to the paint, then I apply wax over the top). It is a really good wax and makes the paint absolutely look like glass, but it shares the downfall of any carnauba wax is it attracts a lot of dust. I'll only need to have taken the car out once or twice and there will be a fine layer of dust sitting on the car.

  • 2 months later...

Here is a picture of my car taken with an SLR camera....should give you guys a good idea of the finish.

Washing every 2 weeks and waxing every 4-6 weeks to protect and maintain the finish.

DAQbnNE.jpg

Oh damn love how it's turned out! all the panels look like they have a sheet of glass over it. love it!

Can definitely tell you've put a lot of hard hours into this and it's payed off!

Good write up with lots of pics, nice car! Its nice to see that your putting a lot of love into it even with the simplest things.

being a daily you'd want it to look nice not only for yourself but to catch eyes, one of my fav cars :worship:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • See if you can thermal epoxy a heatsink or two onto it?
    • The other problem was one of those "oh shit we are going to die moments". Basically the high spec Q50s have a full electric steering rack, and the povo ones had a regular hydraulic rack with an electric pump.  So couple of laps into session 5 as I came into turn 2 (big run off now, happily), the dash turned into a christmas tree and the steering became super heavy and I went well off. I assumed it was a tyre failure so limped to the pits, but everything was OK. But....the master warning light was still on so I checked the DTCs and saw – C13E6 “Heat Protection”. Yes, that bloody steering rack computer sitting where the oil cooler should be has its own sensors and error logic, and decided I was using the steering wheel too much. I really appreciated the helpful information in the manual (my bold) POSSIBLE CAUSE • Continuing the overloading steering (Sports driving in the circuit etc,) “DATA MONITOR” >> “C/M TEMPERATURE”. The rise of steering force motor internal temperature caused the protection function to operate. This is not a system malfunction. INSPECTION END So, basically the electric motor in the steering rack got to 150c, and it decided to shut down without warning for my safety. Didn't feel safe. Short term I'll see if I can duct some air to that motor (the engine bay is sealed pretty tight). Long term, depending on how often this happens, I'll look into swapping the povo spec electric/hydraulic rack in. While the rack should be fine the power supply to the pump will be a pain and might be best to deal with it when I add a PDM.
    • And finally, 2 problems I really need to sort.  Firstly as Matt said the auto trans is not happy as it gets hot - I couldn't log the temps but the gauge showed 90o. On the first day I took it out back in Feb, because the coolant was getting hot I never got to any auto trans issues; but on this day by late session 3 and then really clearly in 4 and 5 as it got hotter it just would not shift up. You can hear the issue really clearly at 12:55 and 16:20 on the vid. So the good news is, literally this week Ecutek finally released tuning for the jatco 7 speed. I'll have a chat to Racebox and see what they can do electrically to keep it cooler and to get the gears, if anything. That will likely take some R&D and can only really happen on track as it never gets even warm with road use. I've also picked up some eye wateringly expensive Redline D6 ATF to try, it had the highest viscosity I could find at 100o so we will see if that helps (just waiting for some oil pan gaskets so I can change it properly). If neither of those work I need to remove the coolant/trans interwarmer and the radiator cooler and go to an external cooler....somewhere.....(goodbye washer reservoir?), and if that fails give up on this mad idea and wait for Nissan to release the manual 400R
    • So, what else.... Power. I don't know what it is making because I haven't done a post tune dyno run yet; I will when I get a chance. It was 240rwkw dead stock. Conclusion from the day....it does not need a single kw more until I sort some other stuff. It comes on so hard that I could hear the twin N1 turbos on the R32 crying, and I just can't use what it has around a tight track with the current setup. Brakes. They are perfect. Hit them hard all day and they never felt like having an issue; you can see in the video we were making ground on much lighter cars on better tyres under brakes. They are standard (red sport) calipers, standard size discs in DBA5000 2 piece, Winmax pads and Motul RBF600 fluid, all from Matty at Racebrakes Sydney. Keeping in mind the car is more powerful than my R32 and weighs 1780, he clearly knows his shit. Suspension. This is one of the first areas I need to change. It has electronically controlled dampers from factory, but everything is just way too soft for track work even on the hardest setting (it is nice when hustling on country roads though). In particular it rolls into oversteer mid corner and pitches too much under hard braking so it becomes unstable eg in the turn 1 kink I need to brake early, turn through the kink then brake again so I don't pirouette like an AE86. I need to get some decent shocks with matched springs and sway bars ASAP, even if it is just a v1 setup until I work out a proper race/rally setup later. Tyres. I am running Yoko A052 in 235/45/18 all round, because that was what I could get in approximately the right height on wheels I had in the shed (Rays/Nismo 18x8 off the old Leaf actually!). As track tyres they are pretty poor; I note GTSBoy recently posted a porker comparo video including them where they were about the same as AD09.....that is nothing like a top line track tyre. I'll start getting that sorted but realistically I should get proper sized wheels first (likely 9.5 +38 front and 11 +55 at the rear, so a custom order, and I can't rotate them like the R32), then work out what the best tyre option is. BTW on that, Targa Tas had gone to road tyres instead of semi slicks now so that is a whole other world of choices to sort. Diff. This is the other thing that urgently needs to be addressed. It left massive 1s out of the fish hook all day, even when I was trying not too (you can also hear it reving on the video, and see the RPM rising too fast compared to speed in the data). It has an open diff that Infiniti optimistically called a B-LSD for "Brake Limited Slip Diff". It does good straight line standing start 11s but it is woeful on the track. Nismo seem to make a 2 way for it.
    • Also, I logged some data from the ECU for each session (mostly oil pressures and various temps, but also speed, revs etc, can't believe I forgot accelerator position). The Ecutek data loads nicely to datazap, I got good data from sessions 2, 3 and 4: https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-2?log=0&data=7 https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-3?log=0&data=6 https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-4?log=0&data=6 Each session is cut into 3 files but loaded together, you can change between them in the top left. As the test sessions are mostly about the car, not me, I basically start by checking the oil pressure (good, or at least consistent all day). These have an electrically controlled oil pump which targets 25psi(!) at low load and 50 at high. I'm running a much thicker oil than recommended by nissan (they said 0w20, I'm running 10w40) so its a little higher. The main thing is that it doesn't drop too far, eg in the long left hand fish hook, or under brakes so I know I'm not getting oil surge. Good start. Then Oil and Coolant temp, plus intercooler and intake temps, like this: Keeping in mind ambient was about 5o at session 2, I'd say the oil temp is good. The coolant temp as OK but a big worry for hot days (it was getting to 110 back in Feb when it was 35o) so I need to keep addressing that. The water to air intercooler is working totally backwards where we get 5o air in the intake, squish/warm it in the turbos (unknown temp) then run it through the intercoolers which are say 65o max in this case, then the result is 20o air into the engine......the day was too atypical to draw a conclusion on that I think, in the united states of freedom they do a lot of upsizing the intercooler and heat exchanger cores to get those temps down but they were OK this time. The other interesting (but not concerning) part for me was the turbo speed vs boost graph: I circled an example from the main straight. With the tune boost peaks at around 18psi but it deliberately drops to about 14psi at redline because the turbos are tiny - they choke at high revs and just create more heat than power if you run them hard all the way. But you can also see the turbo speed at the same time; it raises from about 180,000rpm to 210,000rpm which the boost falls....imagine the turbine speed if they held 18psi to redline. The wastegates are electrically controlled so there is a heap of logic about boost target, actual boost, delta etc etc but it all seems to work well
×
×
  • Create New...