Jump to content
SAU Community

R34 Rear Wheel Bearing

daniels14a
 Share

Recommended Posts

daniels14a Explorer

daniels14a

Posted
Posted

Over the weekend I have noticed an unusual sound from the rear passenger side wheel which i suspected might be the bearing. Over the last few days it has got worse.

So I took the wheel off and it turns out that it is the wheel bearing as there is a little bit of play when moving the top and bottom of wheel back and forward.

Just wondering how hard of a job is it to replace the bearing as I understand that it is held in by four bolts and it is not pressed in.

I do not have any fancy tools so if I was to attack the job, would I managed to get it off and replaced?

Thanks for any advice in advance.

Link to comment
https://www.sau.com.au/forums/topic/429549-r34-rear-wheel-bearing/
Share on other sites
boostn0199 Grand Master

boostn0199

Posted
Posted

Taking the bearing out is easy but then you have to remove the bearing from the spline thats the hard part, youll need to make a few special tools to pull it off. Other problem you run in to is they seprate into 2 pieces when trying to press it off the spline and your left with half still on.

Putting tge new one onto the spline is easy enough if u have a press.

daniels14a Explorer

daniels14a

Posted
  • Author
Posted

OK thank you for the advice.

This is the one which I have just ordered.

http://www.ebay.com.au/itm/360701961813?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1497.l2649

I thought that you have to just unscrew the bolts off the back of it! I did not think that you needed to press or unpress anything!

I think I might just get a mechanic to do the job as I don't have any specialist tools!

daniels14a Explorer

daniels14a

Posted
  • Author
Posted

So looks like this is the wrong bearing. Got it to the garage and they told me that it was missing the top mount for the hand break. After looking around they managed to get one in however once it was all bolted on they realized that the shaft would not fit as it was 3mm to small!

I had no idea that the there different sizes!

Can anyone help me with this as I can not find the correct bearing for my car?

Garage_Kaizen Enthusiast

Garage_Kaizen

Posted
Posted

So looks like this is the wrong bearing. Got it to the garage and they told me that it was missing the top mount for the hand break. After looking around they managed to get one in however once it was all bolted on they realized that the shaft would not fit as it was 3mm to small!

I had no idea that the there different sizes!

Can anyone help me with this as I can not find the correct bearing for my car?

Hey mate, hopefully im not too late on this one.

R34 GT and GTT's are different..

GTT's run the GTR rear hubs and GT/V's run the S13-15 R32-R33 non GTR hubs, the one's you bought off eBay will fit any S and R chassis minus the GTR's and a 34GTT's.. the one you would need is in the link below, its what Just Jap supply but you can see the difference.

http://justjap.com/store/product.php?productid=19774&cat=375&page=1

I hope this helps as most listings for rear wheel bearings miss this very vital piece of info.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I'm actually not sure - I think it was "Stealth Performance" (It really is near impossible to find a FEMALE 1/8BSPT to 1/8NPT male at ALL) but having the thing leveraged on a 90 degree angle on a small aluminium fitting is not too smart. Also in not too smart, I've drilled out the center of the broken fitting so there's maybe 0.00001mm of thread to bite into, so yeah. I may have to get it drilled/tapped/plugged entirely. Given I could conceivably tap a thread/adapter/pressure line in any point in the oil system I suppose it's feasible to run a line to the Nissan Sensor to keep the dash working. Do these exist in AN fittings and the like? Like an AN fitting that has a NPT (or other?) thread as well for putting a sensor in?
    • sonicii
      Anyone running the VQ37VHR with forced induction?

      By sonicii · Posted

      I would agree.  There will be an amount of boost you could run safely with an otherwise factory system, but it would be low enough to not be worth the cost.  And if you are reliving your 20s, you know a 'little bit' was never enough. Personally, if I didn't want to spend the money, then stick with NA bolt-ons, and maybe a tune.
    • Dose Pipe Sutututu
      Mistakes were made, my R34 Story

      By Dose Pipe Sutututu · Posted

      Fuark, at least the motor survived. What brand was the fitting that snapped?
    • GTSBoy
      Anyone running the VQ37VHR with forced induction?

      By GTSBoy · Posted

      Wrong question. There's no point in spending the rather large sum of cash and effort to add turbo, without taking it to the "sensible" limit of the motor itself. If you have to upgrade injectors, etc, then so be it. That is a tiny fraction of what it will cost you to turbo it.
    • GTSBoy
      Starter motor replacment teeth count.

      By GTSBoy · Posted

      Measure voltage at the starter solenoid terminal when the key is at start and it has clicked. If it is really low, then the suspicion falls on the ignition switch (contacts or wiring thereof) as causing a voltage drop instead of sending enough volts to throw the solenoid all the way to engage the starter itself. If it is a decent voltage, then the suspicion is on the solenoid. Might have s horted coil, or might hva dirty contacts. Rip the starter off, dismantle, clean up contacts and inspect winding. It might not be possible to see if there is a short in the winding though. I have a spare starter here that I could measure the resistance of the coil, as a guide to about what it should be, if you need a comparison. <parts hoarder>No you cannot have it.</parts hoarder>
×
×
  • Create New...