Jump to content
SAU Community

My 34 2530 Build

corey.hunter
 Share

Recommended Posts

corey.hunter Explorer

corey.hunter

Posted
Posted

Hi guys,

My R34 RB25 Neo recently spun a big end and has now decided to destroy the turbo, so quiet simply I'm going to ditch the hole setup and start fresh :) my setup will include

RB25DET head:

Camtech 272 9mm lift cams

Supertech Valves, springs, retainers

Bronze valve guides

Quiet a bit of port work

VCT disabled

OS Giken bling bling vernier gears

RB30 block:

Crank, crack tested and balanced

Extended oil pump drive

JE 9:1 pistons

Spool rods

ACL race series mains and big ends

N1 oil pump

1.5mm Restrictors fitted to centre two head oil feeds

Bolt On:

6Boost Highmount mani

GT3540 .82 rear

Turbosmart 50mm gate

SLIDE Industries custom intake manifold with 80mm TB

Bosch 1000cc Injectors

I hope too make around about 500-550 rwhp on pump 98 and possibly once we get some damn e85 make some more power :woot:

Corey

Link to comment
https://www.sau.com.au/forums/topic/430587-my-34-2530-build/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      RB26DETT Sketchy boost mod?

      By GTSBoy · Posted

      There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • GTSBoy
      Cas issue

      By GTSBoy · Posted

      The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Duncan
      RB26DETT Sketchy boost mod?

      By Duncan · Posted

      Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • nash47
      Cas issue

      By nash47 · Posted

      Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...