Jump to content
SAU Community

Mugabetown - Whoretownin' At It's Worst.


Recommended Posts

I agree with you here. Give the motor a heap of KM's on pump98 then give it some e85 when run in has finished.

WHat ECU is it again ? Can it be flex tuned

Yeah thats the idea Scottie.

ECU is Haltech Platinum Pro so eflex is also on the cards ;)

Decisions..... For a decent 34 it's 15 and for a amloast destroyed 33gtr it's 14

This makes it hard because either way I will be fixing stuff and changing, and of it's rooted I can fix it so not to much there, and will have a new engine either way....

Hmm

Grant (Count Grantleyish) is selling his R34 GTT it is really nice - think 14k IRRC.

But he is in VIC and communication may be difficult as he can't hear but give it a try Zac.

Yeah thats the idea Scottie.

ECU is Haltech Platinum Pro so eflex is also on the cards ;)

Thought it was. Well yeah few hundred $$ for the sensor and you're all sweet. Though with E85 so close there's a fair chance it may never see pump98 again after the tune. But its good having that piece of mind that you "CAN" run 98 if you decide to

Don't forget $$$ for the retune also.

I'd be interested to see how a car tuned on E85 would run off boost at highway cruising speeds on 98. It'd be running rich, but i would presume not enough to cause it not to run?

Thought it was. Well yeah few hundred $$ for the sensor and you're all sweet. Though with E85 so close there's a fair chance it may never see pump98 again after the tune. But its good having that piece of mind that you "CAN" run 98 if you decide to

exactly mate. If I want to. But will no doubt be very reluctant ever put 98 after considering its power potential :woot:

Don't forget $$$ for the retune also.

I'd be interested to see how a car tuned on E85 would run off boost at highway cruising speeds on 98. It'd be running rich, but i would presume not enough to cause it not to run?

I drive mine from Caboolture to QR quite often. It runs perfect. chews through a bit of fuel but thats expected

Don't forget $$$ for the retune also.

I'd be interested to see how a car tuned on E85 would run off boost at highway cruising speeds on 98. It'd be running rich, but i would presume not enough to cause it not to run?

If it was a E85 only tune run on 98 running rich would be the least of your worries, the timing advance on E85 is way beyond what an engine on 98 can handle and that's why the flex sensor is important

not that I want to rub it in, but yesterday I spotted another United that has E85 which is close to my home

I have to say that it will soon become more readily available near you too Bunts

If it was a E85 only tune run on 98 running rich would be the least of your worries, the timing advance on E85 is way beyond what an engine on 98 can handle and that's why the flex sensor is important

Would there really be that much timing at low revs and low load though?

not that I want to rub it in, but yesterday I spotted another United that has E85 which is close to my home

I have to say that it will soon become more readily available near you too Bunts

There's no United servos north of the Logan motorway and south of chermside. Not no servos selling E85, no servos at all. :(

If it was a E85 only tune run on 98 running rich would be the least of your worries, the timing advance on E85 is way beyond what an engine on 98 can handle and that's why the flex sensor is important

Wow I totally misread what Peter was saying lol.

Would there really be that much timing at low revs and low load though?

There's no United servos north of the Logan motorway and south of chermside. Not no servos selling E85, no servos at all. :(

I wouldnt want to chance it. Considering i gained 100-110hp changing from 98 to e85 with only 2-3psi more, there is no chance I'd risk running any fuel my car wasnt tuned to fun. Hell I didnt even like putting anything but BP Ultimate in my car before i went e85..

In regards to servo locations. I guess Brendale is closest then. But it is slightly north-er than Chermy

Would there really be that much timing at low revs and low load though?

From my understanding yes, thats why E85 cars often feel like a big capacity NA while cruising around, and while you are cruising it might be ok but the second you put any load on it, say a hill, you would be in the shit.

Wow I totally misread what Peter was saying lol.

I wouldnt want to chance it. Considering i gained 100-110hp changing from 98 to e85 with only 2-3psi more, there is no chance I'd risk running any fuel my car wasnt tuned to fun. Hell I didnt even like putting anything but BP Ultimate in my car before i went e85..

In regards to servo locations. I guess Brendale is closest then. But it is slightly north-er than Chermy

this is what I am currently doing. Will not put anything else in car except for BP Ultimate until it is tuned on E85.

Why take the risk if you don't have to?

From my understanding yes, thats why E85 cars often feel like a big capacity NA while cruising around, and while you are cruising it might be ok but the second you put any load on it, say a hill, you would be in the shit.

ah, ok then. 20l range extenders it is!

next question: tuned on caltex e-whatever, run on united? Caltexs range is lacking out of the cities but there's a nice chain of uniteds around

ah, ok then. 20l range extenders it is!

next question: tuned on caltex e-whatever, run on united? Caltexs range is lacking out of the cities but there's a nice chain of uniteds around

If I were you Peter I'd stick to United. The consistency they have is well known amongst e85 users. They always have a well controlled Ethanol content. Caltex has been knows to drop as low as 70% ethanol, this is a major issue if you dont have a flex sensor.

Also its worth noting that the V8 Supercars this season have in fact ditched Sucrogen E85 in favour of United E85. The same we get from the bowser just "Controlled" tighter to make sure all teams are getting the exact same blend

Either way you decide to go, its always best to get it tuned on the exact same fuel your going to run. Why tune on Caltex if its going to run United?

and their goes another.............

http://finance.ninemsn.com.au/newsbusiness/8823843/300-jobs-lost-as-bp-shuts-brisbane-refinery

Australia's manufacturing industry is in server dire straits.

The correlation between the costs of living and wages needs to be addressed soon, otherwise, Australia is facing a manufacturing sector that will be almost 100% outsourced.

not good.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
    • As MBS suggested if this is happening when the engine is cold you're going to want to remove the intake air regulator and verify resistance + that the shutter is physically opening and closing. At -20C should be fully open, 20C half open, over 60C fully closed. At 20C should be 70-80 ohms. For AAC valve testing using a Consult cable see if you can raise and lower the idle by commanding more or less AAC duty cycle. Hopefully it's pretty linear as well, shouldn't be like 30% AAC valve is barely idling and 40% is 1500 rpm.
    • Bloody apprentices! 🙄
    • Not sure yet.  Was considering speedtek because it was rated to 800hp, but when I did some research about him I don't think I will go for that🤣 So maybe giken gear set, but I'm afraid it won't be strong enough🙄
×
×
  • Create New...