Jump to content
SAU Community

Mugabetown - Whoretownin' At It's Worst.


Recommended Posts

If you can convince the company that they need you and couldn't operate profitably without you, you have a winning argument. Hence $20k raise at the beginning of the year. ;-)

that is very rare, as it is seldom that one person could have such an impact on a business. Especially in the resources sector

that is very rare, as it is seldom that one person could have such an impact on a business. Especially in the resources sector

If I amended that to 'as proftiably' would that be a more correct reflection? Of course, for this to occur, you would need to be at the top or very close to the top - especially within an arm of the business that closely related to sales.

If I amended that to 'as proftiably' would that be a more correct reflection? Of course, for this to occur, you would need to be at the top or very close to the top - especially within an arm of the business that closely related to sales.

it truly depends on the demographics of the business

Yes, if key senior personnel ie executives were to use their position as a bargaining chip to demand an increase in their remuneration package then it may work

Should it he reporting entity though - them auditors would be all over it

Especially the way the public now eyes deeply what how execs are remunerated

In a smaller sized business ie SME - most that are in a top position usually have the ability to influence everyone - making performance bonuses that much easier ;)

  • Like 1

Jawsome!

do tell how!

I was curious too so I did a little digging on the QLD/TMR site and I found this:

Moderately-Powered Vehicle Grounds

You may apply for a certifi cate of exemption if the car you wish to

drive was manufactured before 1 January 2010 and has:

• a supercharged or turbocharged engine, not diesel powered

• a power-to-weight ratio of not more than 125kW/tonne

• no other features of a HPV listed on this form.

You application must be supported by:

• a document published by the manufacturer verifying the

power-to-weight ratio, such as the owner’s manual or

information from the manufacturer’s website; or

• a specifi cation information test report.

A specifi cation information test report is issued by an automotive

service provider and must show:

• the name and address of the organisation(s) that conducted the

test(s)

• the date of the test(s)

• vehicle make, model, VIN/chassis number

• the vehicle’s kerb weight and maximum engine power

• details about the measuring system used to conduct the test,

for example, an engine dynamometer."

From what I've been able to find a stock 33 gts-t would have around 130ish kw/t if you're going off the factory engine and weight figures from nissan. That power to weight ratio wouldn't classify for an exemption however if you were to put the car on a weigh bridge and run it on a dyno it would most likely be under 125kw/t though. So I guess it's all up to which figures they take into account when doing the exemption.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • 3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...