Jump to content
SAU Community

R32 Rb20Det (Idle Problem)

nes 1871

By nes 1871,
in General Automotive Discussion

 Share

Recommended Posts

nes 1871 Enthusiast

nes 1871

Posted
Posted

Hi peeps, I recently bought my first Skyline with some damage to the drivers corner. Panel work is done (: so i started looking at the engine. I started the car and the idle was rough with it idleing high and low very quickly I noticed that one of the injectors where leaking so I pulled them out got my injector guy to have a look at them and he found two to be faulty and need replaced. I got 2 injectors and serviced them and wacked them back in. Started the car it has fixed the rough idle car still seam's to be a little out on idle but rev meter says 900rpm and it idles high and low???? Has anyone had this issue help would be very much appreciated. Thanks guys




I have gone over my hose's with carby cleaner, Blocked my BOV (put a plate over the gasket) and checked my wastgate (not seized)



Link to comment
https://www.sau.com.au/forums/topic/432154-r32-rb20det-idle-problem/
Share on other sites
nes 1871 Enthusiast

nes 1871

Posted
  • Author
Posted

I removed the ACC and cleanded the buid up (there was abit of oil or carbon) still has a bad idle (reving up and down)

I tryed to locate the IAC but couldnt find it but with some help from a helpfull message that was sent from a SAU user (thanks again for the info)

I turned my attention to the air regulator I blocked it started the car and it is still has a bad idle

nes 1871 Enthusiast

nes 1871

Posted
  • Author
Posted

ok guys bit of a mix up by me. Instead of taking off the ACC and cleaning the spring and screw i pulled off the ACC solinode. I just cleaned it and put it back together thanks to DIY search and I then begun to set the idle screw. I disconnected the ACC plug and I found myself closing the screw all the way down to get to 900rpm i open it abit and now im getting 950rpm but car gets to 1200rpm even 1500 sometimes. this happens when i give it abit of throttle car dosnt react when i brake or turn the stearing wheel.

nes 1871 Enthusiast

nes 1871

Posted
  • Author
Posted

ok guys this is where I am today. I went over the intercooler hoses and clamps, cleaned my AFM, cleaned the BOV, cleaned the ACC (spring and screw), cleaned the IAC valve and cleaned the throttle body. after doing all this started the car and same result (idle floats between) 900 and 1200rpm.

I also remembered that a SUA user mentioned the injector seal on the manifold I found that number 1 injector is leaking from the top part of the injector. I removed it and swiched the seals with number 2 and number one still leaked. My injector guy will receive a very happy call tomorrow. I have tryed to set my idle screw (ACC) but cant get a good idle I think due to the injector leaking.

oh I also pumped the brakes continues and the idle went down pretty fast??? I think the booster has a vac leak causing this idle???

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...