Jump to content
SAU Community

Gtr R34 Wheel, Tyres, S-Tune Suspension, Steering Wheel And More.

kkangi80
 Share

Recommended Posts

kkangi80 Contributor

kkangi80

Posted
Posted

Hi

I need to sell these items..

1. R34 GTR wheels, cabs and Falken Azenis 615K 265 35 18

- wheels good condition and tyres are around 25% left.

- $1300.00

2. R34 GTR S-tune suspension

- heasman steering cheked and good condition

- $850.00

3. R34 GTR steering wheel red stich with air bag

- $450.00

4. Nardi deep cone 350mm

- used and fair condition

- $200.00

5. Hankook r-s3 265 35 18

- around 1000km and more than 90%

- $850.00

6. Yokohama advan a050 265 35 18

- 2 for 40% and 2 for 15%

- $200.00

Picture will be upload before end of this week.

I am in sydney and please contact to

[email protected]

Thank you

kkangi80 Contributor

kkangi80

Posted
  • Author
Posted

Hey mate

can you plz send a pic of the r34 gtr steering wheel to

[email protected]

Wanting to know condition

Hi

I sent a email to you.

Thank you

  • Like 1
kkangi80 Contributor

kkangi80

Posted
  • Author
Posted

Will the suspension fit an r33gtr? From what I have read it will but just thought you might be able to confirm.

Sorry I do not know.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      So I actually had the cover off my car today, here is a (bad) pic of the setup. I have an oil cooler thermostat block, the temp sender is straight in there. The pressure sender has a short AN line to a T piece which is mounted (hopefully cable tied counts as mounted....) on the chassis. BTW every fitting you could ever imagine exists....just depends what they cost and how many you need. Raceworx AN adapters are here: https://raceworks.com.au/fittings/adapters/, I think you said you need BSPT to AN (https://raceworks.com.au/fittings/adapters/bsp/tapered/an-to-bspt-adapters/) and AN to NPT (https://raceworks.com.au/fittings/adapters/npt/) BTW, braided line is super simple to make. It looks intimidating, is not.
    • Duncan
      NC MX5

      By Duncan · Posted

      Perfect day for a pie, really needs a soft top in this weather though
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Prime parking, she is a little girl...LOL
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I'm actually not sure - I think it was "Stealth Performance" (It really is near impossible to find a FEMALE 1/8BSPT to 1/8NPT male at ALL) but having the thing leveraged on a 90 degree angle on a small aluminium fitting is not too smart. Also in not too smart, I've drilled out the center of the broken fitting so there's maybe 0.00001mm of thread to bite into, so yeah. I may have to get it drilled/tapped/plugged entirely. Given I could conceivably tap a thread/adapter/pressure line in any point in the oil system I suppose it's feasible to run a line to the Nissan Sensor to keep the dash working. Do these exist in AN fittings and the like? Like an AN fitting that has a NPT (or other?) thread as well for putting a sensor in?
    • sonicii
      Anyone running the VQ37VHR with forced induction?

      By sonicii · Posted

      I would agree.  There will be an amount of boost you could run safely with an otherwise factory system, but it would be low enough to not be worth the cost.  And if you are reliving your 20s, you know a 'little bit' was never enough. Personally, if I didn't want to spend the money, then stick with NA bolt-ons, and maybe a tune.
×
×
  • Create New...