Jump to content
SAU Community

R33 Shut Off After Radiator Went

cree

By cree,
in General Automotive Discussion

 Share

Recommended Posts

cree Community Regular

cree

Posted
Posted

Today my radiator went as I was driving along the highway. When the radiator went the car shutoff straight away. Is this a safety thing that R33's have or is there something more wrong with the car? I did a search but I didn't find anything which is why I think it may be something else wrong.

Link to comment
https://www.sau.com.au/forums/topic/433222-r33-shut-off-after-radiator-went/
Share on other sites
colourclassic Mentor

colourclassic

Posted
Posted

I just put a whole lot of water in the radiator and tried to start still no luck. I also noticed it all just ran out from the bottom of the radiator.

An undamaged engine will start and run without a drop of water in the cooling system for a prescribed, short amount of time. Your engine has been damaged by overheating, assuming it was running fine before all of this happened.

How long did you run the engine after you noticed the first signs of steam coming out? Tell me you got it towed off the highway rather than running it dry?

cree Community Regular

cree

Posted
  • Author
Posted

So I just thought if try the car this morning and it did start but it doesn't sound at all healthy. I only ran it for a few seconds then shut it off. It making a really lounge ticking noise like its dropped a cylinder of something.

StevenCJR31 Veteran

StevenCJR31

Posted
Posted

Yeh I should have. Oh well I'll put a new radiator in and see how it goes.

A new radiator wont fix the motor, sounds like a blown head gasket at the very least-

You can do a compression test to determine the condition of the engine

  • Like 1
colourclassic Mentor

colourclassic

Posted
Posted

Get a new radiator and fill it up with fresh liquid.

My peugeot wouldnt turn on without anything in the radiator, it was a safety feature. Perhaps 33s have the same gig.

That being said, im not game to turn on my 33 without coolant...

Dude you just told everyone you own a Peugeot? Not cool man...

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Cas issue

      By MBS206 · Posted

      Have you done the Ignition Sync Wizard in the AEM software?
    • MBS206
      R32 GTS (RB20DE) Injectors Replacement

      By MBS206 · Posted

      Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • MBS206
      RB25DE NEO with Haltech ECU

      By MBS206 · Posted

      You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • sonicii
      Could it really happen......

      By sonicii · Posted

      I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...