Jump to content
SAU Community

Recommended Posts

Hey my mate got an r32 gtst the other day and we are Having trouble with the Parker lights, the Parker lights come on when key is turned on accessories and does not come on when you turn the switch on, I had a look behind the dash cluster to see any sign that it was tampered with but all seems normal, its not switch because with out the dash cluster plugged in and surround with the switch not plugged in it still happens, however the plug that plugs into the park lights and drive lights looks to be a slightly melted and black on two plugs as if there is a short somewhere. note that it is not blowing fuses Opinions?

Link to comment
https://www.sau.com.au/forums/topic/434307-r32-parker-lights-on-when-key-on/
Share on other sites

When you refer to "parker lights", are you including the rear park lights, front park lights and dash lights all coming on? and then all going off when the switch turned on?

Sounds like a earthing problem.. Do the low beam and high beam all work correctly? What happens when the key is out of the ignition and you try turn the park lights on?

Yes when the key is turned to accessories the dash lights come on Parker lights front and back and that beeping sound, and when key is off it all turns off, when key off an you turn Parker's on from the switch there's nothing turn the switch again and driving lights come on

Because of the low current draw on the park light circuit, a short can light up the parks tails and dash quite easily.

I would try an isolation test. I am not sure how the lights are wired but - have the key on and the park light switch off.

I would start in the engine bay - find the plug nearest to the drivers side parkers and unplug it. What happens? Plug it back in and try the passenger side. What happens? Now try both the tail lights one side at a time, noting what happens then plug them back in to try the other side (should be behind the material in the boot) If no plugs are found, remove the globes instead (careful - hot)

When you turn the switch on for park lights, do they glow slightly brighter?

Voncina I tried what you said and nothing also the driver headlight is not working have changed the globe still nothing got a test light on it and no power to the plug but when I pull the stalk it had power, I had a similar problem with mine but ended up being I had to change the dash cluster and it fixed up but I also had no rpm signal and temp gauge so can't be that I'm thinking the old owner hooked the turbo timer and or electronic boost gauge up wrong causing a short maybe? We have traced the loom back all seems fine and there is power at the fuse box also

I highly doubt that if something like an ebc or turbo timer is wired incorrectly in the dash would somehow affect only the drivers side headlight.

If you have tested at the stalk and are getting power there, and none at the light, chase the harness back from the light, checking for any wear on plugs, harnesses - where they go through grommets are usual bad spots. If the passenger side is working, and the drivers is not - find where the harness T's off for the passenger side/drivers side and the fault will most likely be between the T and the faulty light.

Hope I am helping.

Update, I pulled turbo timer out and electronic boost gauge and head unit out to find the Parker light problem, the boost gauges power source was coming from the headunit as there is a Parker wire (blue/red) witch is ilumination for factory headunit and they had tapped into this causing the Parker's to have power when the key is in on position, however I still have the driver side headlight not working

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Has equal chance of cleaning an AFM and f**king an AFM. I think you can work out what happened. When the Hitachi ECU sees the AFM die and goes into the associated limp mode, then it will start and run just fine, because it ignores the AFM and just runs on idle maps that will do what it needs to get it going. But there is no proper load signal, so that's about all it can do. My suggestion? If you don't want to go full aftermaket ECU, then get some R35 GTR AFM cards and some housings to put them in, in the stock location, and Nistune the ECU. Better to do a good upgrade than just replace shitty 40 year old tech with the same 40 year old tech.
    • So my car was recently having trouble starting on initial crank, I would need to feather the gas for it to start up but besides that it would start and run fine. So I clicked the idle air control valve (with throttle body cleaner) and cleaned the MAF sensors (with MAF cleaner). The start up issue was fixed and now the car turns over without the assist of the throttle, but the car is in limp mode and wont rev past 2.5k RPM. From what I understand the IACV would not put the car in limp mode, so I am to believe it is the MAF sensors, but it was running fine before and now I cant get it out of limp mode. I cleaned the MAF made sure the o rings were seated properly. Made sure the cables were plugged in properly, the cables also both read the same voltage. Does anybody know why this is or what could be causing this or how to get it out of limp mode?
    • Ooo I might actually come and bring the kids, however will leave the shit box home and take the daily
    • Thanks. Yeah I realised that there's no way I'd be able to cover the holes with the filler, it would just fall through. Thanks again @GTSBoy!
    • That was the reason I asked. If you were going to be fully bodge spec, then that type of filler is the extreme bodge way to fill a large gap. But seeing as you're going to use glass sheet, I would only use that fibre reinforced filler if there are places that need a "bit more" after you've finished laying in the sheet. Which, ideally, you wouldn't. You might use a blob of it underneath the sheet, if you need to provide some support from under to keep the level of your sheet repair up as high as it needs to be, to minimise the amount of filler you need on top. Even though you're going bodge spec here, using glass instead of metal, the same rules apply wrt not having half inch deep filler on the top of the repair. Thick filler always ends up shitting the bed earlier than thin filler.
×
×
  • Create New...