Jump to content
SAU Community

Help! Wanting To Replace My Injectors In My R31 (Rb30)


Recommended Posts

Hi guys!!

Just wondering if anyone out there could tell me exactly how to replace my injectors. I'm putting standard ones back in. My car is running like crap an was told they need to be replaced. I am female and do not know a lot so any help is greatly appreciated.

Thank you. :)

Unplug the wiring and then unbolt the fuel rial and remove the fuel lines and pull them out. A bit of fuel will spill out when disconnected. They just sit there held in by the fuel rail. You might have to remove the manifold if it is in the way. You will need to get the same size that is in there all ready. If you have aftermarket ones and you put stock ones back in without a tune it will run even more crap. Make sure the plugs for the wiring is the same. If they are aftermarket they could of been cut and modified.

It's not a hard job but if you don't know much about engines I would give it to someone to fix.

The old VL injectors had rubber hose on the feed, not sure about the R31 injectors but the VL ones looked like a pain to change without the common fuel rail.

It's not something you want to get wrong...

Seems like an easy job, but if you say that I can't make a mistake then maybe I will he someone to help or just give it to someone to do for me. Thanks so much for your helps guys. Ill have a look an if I think ill stuff it up ill get someone else to do it. Thank you! Your help is much appreciated :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So many people don't notice it, as batteries decay slowly over time. Two big reasons people end up noticing and needing to replace batteries: 1) The cold weather. The cold not only makes it harder to turn the engine for a few reasons, but it also increases the batteries internal resistance. So this means you need MORE power to turn a colder engine, AND the battery has a lower limit on how much current it can provide. 2) Something gets modified/altered/added in the wiring, typically an aftermarket accessory, like a dash camera, or an alarm etc, and this adds a small amount extra onto the battery, and pushes it over the edge in its failing days. But if you hadn't have read this thread, and just pushed through, chances are you might have made it through this winter, just. But come next winter, it would have been kapoot. But the fact you changed it out now, means you've instantly noticed how much nicer it is for starting, and will be less worry for you that the engine won't start now.
    • Holy shit, I'm glad you brought up the battery issue and I'm glad I asked about measuring it. Old battery was at a healthy 12.82V in the morning with the car turned off. Removed the fuel pump fuse, clamped the multimeter on at min/max/average and cranked for ~3 seconds. It dropped down to 8.30V. So yeah, not surprising it struggled that much. Picked up a fresh battery from supercheap and it's ridiculous. Haven't done a cold start yet, but man, even with a warm start the difference is night and day. I can't believe I lived with this for so long. Just blamed it on it being an old modified car. Went with Century because convenient. If they are shit it'll be a future me problem. But just in case I set up a reminder for 30 months - 8 weeks to check on the battery state and get a warranty replacement if necessary. 
    • There's another sensor that sits inside the evaporator, that's a C U N T to get to, but can be done without removing the entire unit. Usually it's not the sensor that dies but the actual capacitor in the circuit (part of the plug that dies).  
    • Putting the climate control CU into diagnostic mode is independent of the ECU. You just have to do the dance prescribed in the manual. No, I do not know what the dance is. I have an R32, so use the dance in the R32 manual. On older cars, I would have said "no, the ECU should not affect whether the A/C works".... but for an R34 that might be wrong. I don't recall the detail, but there was extra mods required to make my R32 A/C work against the R34 ECU. The R34 ECU apparently gets involved in the running of the A/C more than earlier cars did. Theoretically, if the PFC is a true plug in, then it should just work the way that the original ECU does - wrt A/C. But there's always scope for them to have not cared. Nope. Pressure switch out = getting the fridgey out to pump the gas out before pulling the switch. The switch really cannot sense gas pressure unless it is up against the gas.
×
×
  • Create New...