Jump to content
SAU Community

Recommended Posts

Hi Guys,

I purchased my skyline like this and i believe they scratched it installing the backyard japspec headunit that had i kid you not over 100 cables shoved in behind the head unit and carpet which was a nightmare to remove.

Do you guys have any pointers on restoring this? Or is it best to just find a replacement and swap it out.

Cheers,
Peter

2q1xp2x.jpg

Edited by petery3
Link to comment
https://www.sau.com.au/forums/topic/434488-restoring-interior-paint/
Share on other sites

well its not paint its just plastic which is scratched.

easier to get a replacement but.

there are guys who can do plastic repairs, basically they heat it up and smooth it out then when its hot and plyable then press on a paterned material to match whats there and your done.

well its not paint its just plastic which is scratched.

easier to get a replacement but.

there are guys who can do plastic repairs, basically they heat it up and smooth it out then when its hot and plyable then press on a paterned material to match whats there and your done.

what would the most cost effective solution be? also what do you even call that part of the car? is it apart of the center console or?

here's a tip for you, most cost effective TEMPORARY - mid term solution = get some black shoe polish and a cloth, and buff it out. By buff it out obviously i don't mean it will buff out but the polish will fill in the scratches and it won't be very noticeable, to the point that if you don't pay attention you wont notice them there.

That of course depends on how deep those scratches are, though yours looks as bad as mine, so yeah it'll work.

here's a tip for you, most cost effective TEMPORARY - mid term solution = get some black shoe polish and a cloth, and buff it out. By buff it out obviously i don't mean it will buff out but the polish will fill in the scratches and it won't be very noticeable, to the point that if you don't pay attention you wont notice them there.

That of course depends on how deep those scratches are, though yours looks as bad as mine, so yeah it'll work.

This did the job for me :yes: .. though i didnt have many scratches to begin

  • 3 weeks later...

So what exactly is this replacement part called lol? It's not exactly a centre console or anything

It looks like the lower part of the dash, so apart of the dash pad. I would be looking for a complete dash in good condition.

I'm in the same boat as you but im also looking for a way to freshen up the plastic trims around the gear selector all the way up to the tripple gauges. They've gone all soft/mouldy sort of.

Anyone with ideas ?

The DIY section has a good write up on respraying the plastic trim with spray cans. could look into that. otherwise parts are always available just gotta look a bit :)

Bronson.

Edited by Bronno!

I'm in the same boat as you but im also looking for a way to freshen up the plastic trims around the gear selector all the way up to the tripple gauges. They've gone all soft/mouldy sort of.

Anyone with ideas ?

sand back lightly, then respray. that's about it, apart from getting a custom dash getting made up. i know who can do that for you though.

Yeah I was thinking of doing that but I want to get it as close as possible to the rest of the dash .

It must be the aussie heat and the quality of the trims because it only happens around the gear selector trims and radio. The rest of the dash trims are perfect condition.

Was thinking of cleaning the trims and vinyl wrapping it but the trims seem very fiddly especially the corners and cigarette lighter

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm looking for some real world experiences/feed back from anyone who has personally ran a EFR7670 with a 1.05 exhaust housing or a .83 I'm leaning towards the .83 because its a street car used mostly for spirited driving in the canyons roads. I"m not looking for big numbers on paper. I want a responsive powerband that will be very linear to 8000 rpm. I dont mind if power remains somewhat flat but dont want power to drop off on top. The turbo I've purchased is a 1.05, although the mounting flange T3 vs T4 and internal vs external waste gates are different on both housings, I not concern about swapping parts or making fabrication mods to get what I want. Based on some of the research I've done with chat gpt, the 1.05 housing seems to be the way to go with slightly more lag and future proofing for more mods but recommends .83 for best response/street car setup. AI doesn't have the same emotions as real people driving a GTR so I think you guys will be able to give me better feed back 😀   
    • Surely somebody has one in VIC. Have you asked at any shops?  Is this the yearly inspection or did you get a canary?
    • This is where I share pain with you, @Duncan. The move to change so many cooling system pieces to plastic is a killer! Plastic end tanks and a few plastic hose flanges on my car's fail after so little time.  Curious about the need for a bigger rad, is that just for long sessions in the summer or because the car generally needs more cooling?
    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
×
×
  • Create New...