Jump to content
SAU Community

Brembo Evo9 Calipers + Pmu Rotors + S/r Chassis Adaptors

d1a31
 Share

Recommended Posts

d1a31 Collaborator

d1a31

Posted
Posted

Im taking parts of my cefiro so this front brake kit is up for sale.

This is a straight bolt on for S13 S14 R32, the last photo shows the difference between a r32 4 pot front caliper

The calipers are off an evo9, the rotors are top of the line Project Mu SCR PRO 2 piece items with a RRP of $1355 !!

The adaptor plates are by Touge Factory in the USA

I don't have any verniers to accurately measure rotor thickness, these have seen 5 or 6 hard circuit days and the rest has been drift use.

The calipers need new pads otherwise ready to go, Im after $1400 for the lot in Adelaide Cheers Chris 0401 483 906

brembo1_zps65f21b1e.jpg

brembo2_zpsb520a8b8.jpg

brembo3_zps702a1564.jpg

  • 2 weeks later...
  • 2 weeks later...
  • 2 weeks later...
simdog Collaborator

simdog

Posted
Posted

Would the adaptor plates fit a 33? If not could you PM me a price for just the calipers. Would need them posted to Brisbane 4073.

Cheers

«Cyph3r» Experienced

«Cyph3r»

Posted
Posted

Would the adaptor plates fit a 33? If not could you PM me a price for just the calipers. Would need them posted to Brisbane 4073.

Cheers

They'll bolt straight onto a 33 as well, s13/14/15 r32/33 are all the same spacing, offset etc so long as 5 stud model. Only different r chassis is 34 which uses slightly larger bolt holes with same centre to centre distance.

d1a31 Collaborator

d1a31

Posted
  • Author
Posted

The rotors are factory evo sizing so 320x32 Its a good adaptor kit really as factory evo rotors can be used or any of the many available aftermarket replacement rotors in factory evo size.

ROBAPHENT Contributor

ROBAPHENT

Posted
Posted

Yeah i use to have a EVO 6 the stopping power of a stock EVO system with a good set of pads was awesome. this could be next level and more then enough for most people (Cyber evo use to run this same setup on there evo)

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      Wheel Sizes & Offsets For Skylines

      By The Bogan · Posted

      The speedo's can be very conservative, when my Mazda NC MX5 speedo is showing 118kph, the GPS, and a calibrated radar.... cop mate.....hits me at around 110kph +/- 1 or 2 kph, and that is on a 215/45 17, stock tyres size is 205/45 17 as well, so weirdly conservative with stock tyre size When my Commodore speedo red 116kph GPS had me at 110kph After doing some offset and clearance measurements to see what can fit the NC on 17x8 +40, without guard rolling or rubbing anything at my current ride height, I've decided that when my tyres are toast, I'm going to fit 225/45 17 and see where that gets me IRT actual speed of my speedo and GPS/radar From the online calculator I should be still be doing around 5kph under an actual 110kph when the speedo is showing 110kph My ADHD requires that when I'm doing 110kph on the speedo, that the actual road speed is actually really close to that, and not alot slower And going from 205 to 225 still keeps the car within the %/mm allowable in the NSW vehicle rules and regulations, which is nice, as long as I'm looking at the latest version that is.....LOL https://www.nsw.gov.au/sites/default/files/2021-02/RMS-13.464-Light-vehicle-modifications-Vehicle-Standards-Information-No-6-November-2013.pdf
    • MBS206
      R34 25GT Engine Light 21

      By MBS206 · Posted

      Take the value it measured as, and pick the closest range available that is above the reading on the screen.   Also, no point just testing the coils. Read what has been said again. You need to test all your wiring, everything.
    • GTSBoy
      R34 Handbrake light saying ON and intermittently flashing

      By GTSBoy · Posted

      Does the scanner do all the CUs in the car, or only the ECU?
    • albyz34gt
      R34 N/a And R34 Turbo (gtt) Transmission.. Uh, Problem.

      By albyz34gt · Posted

      @666DAN sorry to bring you and old thread.     I've got my de+t done and it's all running great other than 1 small issue.    Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd when selected . But nothing when in  drive or what gear your in when you pop it into tiptronic. I'm sure there is maybe 1 wire in the ecu plug I need to move to rectify this. Do ya have any ideas?     Cheers man
    • RB25inside
      R34 Handbrake light saying ON and intermittently flashing

      By RB25inside · Posted

      Well I recently changed my rear axles and was thinking if I bumped anything, I have been driving the car for a while now though... But it has been raining today so everything is wet under the wheel arches. Brakes feel fine and can't hear any of the metal screamers, I had a squeak coming from one of the handbrake drums but that seems to have gone away a while ago. I was going down a hill when it lit up and I did feel the abs bite for a second and question why it did it?
×
×
  • Create New...