Jump to content
SAU Community

Recommended Posts

I have one in brisbane. It's been rebuilt in 2006 and had only done about 5000-10,000km max before the car it was in was rear ended. It is a series 2 block and has 20 thou over acl cast pistons, standard rods and acl bearings. i believe the block may also have been decked slightly. make an offer if you want it. I don't want too much for it as I have too many engines around at the moment. I also have a good running series 1 rb30 out of my one owner vl wagon that i recently bought off the original eldery owners. It will be out of the car within the next week or so.

I have a bare RB30 block (not sure what series) with crank and cradle that came out of a VL wagon. Not sure of kms.

Will let it go for $300.

Located in Wollongong NSW.

First up sorry for the delay... Been flat out these last 2 weeks :(

I have a bare RB30 block (not sure what series) with crank and cradle that came out of a VL wagon. Not sure of kms.

Will let it go for $300.

Located in Wollongong NSW.

Bare RB30 block is good... Does it have the machine area at the front to fit a new tensioner and does it have the holes for the turbo lines on the right side of the block?

To be honest, $300 is very pricey. Can get the whole motor for $350-$400. What's the lowest you'd go???

I have one in brisbane. It's been rebuilt in 2006 and had only done about 5000-10,000km max before the car it was in was rear ended. It is a series 2 block and has 20 thou over acl cast pistons, standard rods and acl bearings. i believe the block may also have been decked slightly. make an offer if you want it. I don't want too much for it as I have too many engines around at the moment. I also have a good running series 1 rb30 out of my one owner vl wagon that i recently bought off the original eldery owners. It will be out of the car within the next week or so.

Hey bud, sounds pretty decent. Just need you to give me a starting point for a price - don't want to unintentionally throw a ridiculous price at you. Plus I gotta figure put how much it will cost to get it freighted to Sydbey!

Ill have to check it for you mate. Havent had a look at it for a while. Its just been sitting in the garage for a fair bit. Ill check tomorrow and let you know.

Mate if you give me $200, you can take it.

  • Like 1

Ill have to check it for you mate. Havent had a look at it for a while. Its just been sitting in the garage for a fair bit. Ill check tomorrow and let you know.

Mate if you give me $200, you can take it.

Thanks dude :)

Thanks dude :)

Hey Joey,

Got some pics to send to you of the front and side of the block.

Send me your number and ill mms them to you.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
    • I assume clearances were all a-okay?
    • Shock tower brace is in +5Kw....LOL  
×
×
  • Create New...