Jump to content
SAU Community

Recommended Posts

Just thought id start a little topic about the few good tuners that we have in Canberra. Who do you use and why? Also what ecu's your tuners specialize in.

Please everybody put out your opinions and why.

This info hopefully helps anyone looking to tune there car get a rough idea on who they are going to go with.

Cheers guys

Cuong...

Link to comment
https://www.sau.com.au/forums/topic/435375-tuners-in-canberra/
Share on other sites

Hey guys I'm running a haltech platinum in my r33 gtst. As much as ed from Autotech hates haltech's, he tune my car for me.

I'd like to say the guys out at Autotech are very friendly and offer great customer service.

Ed himself I'd highly recommend as a tuner in Canberra as there are only a handful of them around. He was very helpful with any question that I had and really knew what he was doing.

Although if I had a choice of ecu because Ed is my tuner i would have gone with an autronic, Ed is canberra authorized dealer for them and he highly recommends them.

Ed wasn't the first person that came to mind when it came to tuning my car but a friend of mine recommended him to me and he was happy to get me in almost straight away, I went with him.

I'd like to say I'm very happy with my tune, although we could have pushed more out of it we chose not to as we wanted it to be a safe tune. Car runs very and I'd have to say that I've had a lot of different tuners tune my cars over the years this would have to be the best place I've ever been too & I'm a picky guy.

Good tuners are hard to find that's why I'm posting this up. Anyone unsure on who to tune there car I'd highly consider Autotech.

The boys there will take care of you.

Thanks everyone.

Regards Viet

Subject covered many times and there is a sticky at the top of this forum. http://www.skylinesaustralia.com/forums/topic/41527-where-to-get-skyline-serviced/page-35

Boils down to choose who you feel comfortable with. Each one of these shops below had/has issues with vehicles that have shit themselves.

Certain shops have ECU Tuning preferences. For me at the moment:

Ed (Autotech) tunes my 34GTT - Nistune (Autronics & Nistune dealer)

Glen (ESP) tunes my 32 GTR - Haltech (Haltech & Vipec's)

John (Trojan) does all my mechanical - coz I trust him, he's experienced and VERY helpful. (Jake does the Tuning and as far as I know will do any ECU)

Some folks use Ultimate Tunes.

I'm not tied to any shop. If asked would recommend any of the above based on what is required to be done.

If I have a bad experience I change shops and they loose my business, and sometimes my Skyline buddies will avoid the shop.

If any of these contributed to critical engine failure I take them to task over it.

Engine builds are best done interstate in my Opinion. Croydon's (CRD) built mine. Racepace I hear good things about. JEM is changing hands

Bolt on's and tuning as I said above is who you feel comfortable with.

Edited by Sinista32

Oh and I should add if you have an engine built get them to tune it after run in. Then there is no pointing of fingers if the worst happens within the warranty period.

My cars are not heavy hitters either. The closer you drive it to it's limits and beyond the closer you are to your next rebuild.

Shit happens and some drivers contribute greatly to the failure. No car is bullet proof. If you ring it's neck it will die.

Treat your car within tolerances and it will look after you.

Thanks for all replays. It gets boring in our a.c.t section so a bit of talk here and there keep it more interesting lol.

I'm no knocking any work shops I'm just very happy with the service and workmanship I received at Autotech. So that's why I'm recommending them.

I also had a little issue with my tune as it was a tad rich leaving black up the back side of my car. Ed booked me in and had to stay back to 7.30 to chuck my car on the dyno and run over things again. He ended up dialing up more boost for me and checked through it all.

He did all this for me free of charge as he said he wanted to keep me happy. I don't know to many tuners like that.

I am Just a happy customer.

He did all this for me free of charge as he said he wanted to keep me happy. I don't know to many tuners like that.

I am Just a happy customer.

I basically had the same experience at Trojan.

Free Retune to achieve what I originally wanted, but due to some issues, didn't get first time round.

Subject covered many times and there is a sticky at the top of this forum. http://www.skylinesaustralia.com/forums/topic/41527-where-to-get-skyline-serviced/page-35

Boils down to choose who you feel comfortable with. Each one of these shops below had/has issues with vehicles that have shit themselves.

Certain shops have ECU Tuning preferences. For me at the moment:

Ed (Autotech) tunes my 34GTT - Nistune (Autronics & Nistune dealer)

Glen (ESP) tunes my 32 GTR - Haltech (Haltech & Vipec's)

John (Trojan) does all my mechanical - coz I trust him, he's experienced and VERY helpful. (Jake does the Tuning and as far as I know will do any ECU)

Some folks use Ultimate Tunes.

I'm not tied to any shop. If asked would recommend any of the above based on what is required to be done.

If I have a bad experience I change shops and they loose my business, and sometimes my Skyline buddies will avoid the shop.

If any of these contributed to critical engine failure I take them to task over it.

Engine builds are best done interstate in my Opinion. Croydon's (CRD) built mine. Racepace I hear good things about. JEM is changing hands

Bolt on's and tuning as I said above is who you feel comfortable with.

I've used crd when I was living in Sydney as well. The are prob one of the workshops I'd highly recommend.

I basically had the same experience at Trojan.

Free Retune to achieve what I originally wanted, but due to some issues, didn't get first time round.

Trojan are very good no one knows skylines like. John in Canberra. He was who I originally wanted to tune my car but it's like a 4 weeks waiting list which was inconvenient for me.

I basically had the same experience at Trojan.

Free Retune to achieve what I originally wanted, but due to some issues, didn't get first time round.

Myself included. Wielded a few parts on my car as well as a few other things he did free of charge(:

I also use Bob Jane in Belco for tyres - extremely nice staff and always give discounts :)

I would say trojan as well. John is the guru of skylines.

Have always went to him, yes his prices are sometime a little too high but he is the only person i trust

Also he has a dyno on the floor which is so good for cars which are too low

My brothers R34 with Apexi SAFC was tuned my him.

Edited by 5hiv

All tuners will have horror stories and good things said aobut them.

Get quotes from the major shops in canberra

and go from there based on price vs customer service. Some shops that treat 1 person really well might fk over someone else. So just go on your gut feeling.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I personally would go with cutting out the rubber. Then deal with getting sleeve off separately. Rubber can be painful to cut, it loves to jam up cutting tools. I normally have success with drill bits, deburr bits, angle grinders, jigsaw, reciprocating saw, and never forget... fire. Obviously different tools won't work in all locations you're trying to work with, and you need to be comfortable with each. You personally may be happy slowly slicing it out with a razor blade, if you are, go for it with one too! Feel free to wait for others to weigh in also on their thoughts.
    • So ... I got everything disconnected and started dropping the frame. Three of the four mounts started to come down but the fourth one (the one with the nut that gave me all the trouble) won't budge. The inner metal sleeve stays up tight against the chassis rail although the outer part of the mount drops a bit (and can be levered quite a lot more) but it's just stretching the rubber bushing. So I reckon there's some serious corrosion inside the inner sleeve and holding it tight to the lug at the top of the bolt. Tried everything I can think of so far: penetrating oil, whacking the top of the sleeve to vibrate it and wedge a screwdriver blade in there. I also tried to turn the inner sleeve a bit by hitting it with a chisel at the bottom. It's stuck solid. What do you think about cutting the rubber with a blade so I can drop the subframe around it anyway. Then worry about getting the inner sleeve off after? Will that work? Is it gonna give me even more problems?
    • Steam valve seals are usually responsible for cold start smoke, it goes away once engine warmed up. Disconnect it let engine breathers and let it breath freely, see if problem goes away after a short drive. Also check to make sure engine oil drain pipe is not blocked or kinked. 
    • Haha thanks! Yea I'm moving over from 2x 1000cc jets pre throttle over to 6x 190cc direct port jets and 1x 500cc pre throttle jet.  Direct port comes with all the advantages you would expect, except that pre throttle does cool down IAT'S more. That's why my direct port nozzle placement is closest to the plenum as possible in the runners to allow the air more time to cool before being sucked in. I'm also putting that one 500cc pre throttle jet to help with more cooling. It's a hybrid system. There's a lot more advantages to moving over to a PWM solenoid with a constant pressure system vs my old PWM pump setup, but I'll get more into that once I'm done converting everything over. The ricer in me is excited to see SS tubing all over my manifold though!
    • Very cool, see what I did there? 🥲 Wild WMI setup, first I've seen where it's on each cylinder runner, usually I see a single jet pre throttle.
×
×
  • Create New...