Jump to content
SAU Community

Recommended Posts

Just thought id start a little topic about the few good tuners that we have in Canberra. Who do you use and why? Also what ecu's your tuners specialize in.

Please everybody put out your opinions and why.

This info hopefully helps anyone looking to tune there car get a rough idea on who they are going to go with.

Cheers guys

Cuong...

Link to comment
https://www.sau.com.au/forums/topic/435375-tuners-in-canberra/
Share on other sites

Hey guys I'm running a haltech platinum in my r33 gtst. As much as ed from Autotech hates haltech's, he tune my car for me.

I'd like to say the guys out at Autotech are very friendly and offer great customer service.

Ed himself I'd highly recommend as a tuner in Canberra as there are only a handful of them around. He was very helpful with any question that I had and really knew what he was doing.

Although if I had a choice of ecu because Ed is my tuner i would have gone with an autronic, Ed is canberra authorized dealer for them and he highly recommends them.

Ed wasn't the first person that came to mind when it came to tuning my car but a friend of mine recommended him to me and he was happy to get me in almost straight away, I went with him.

I'd like to say I'm very happy with my tune, although we could have pushed more out of it we chose not to as we wanted it to be a safe tune. Car runs very and I'd have to say that I've had a lot of different tuners tune my cars over the years this would have to be the best place I've ever been too & I'm a picky guy.

Good tuners are hard to find that's why I'm posting this up. Anyone unsure on who to tune there car I'd highly consider Autotech.

The boys there will take care of you.

Thanks everyone.

Regards Viet

Subject covered many times and there is a sticky at the top of this forum. http://www.skylinesaustralia.com/forums/topic/41527-where-to-get-skyline-serviced/page-35

Boils down to choose who you feel comfortable with. Each one of these shops below had/has issues with vehicles that have shit themselves.

Certain shops have ECU Tuning preferences. For me at the moment:

Ed (Autotech) tunes my 34GTT - Nistune (Autronics & Nistune dealer)

Glen (ESP) tunes my 32 GTR - Haltech (Haltech & Vipec's)

John (Trojan) does all my mechanical - coz I trust him, he's experienced and VERY helpful. (Jake does the Tuning and as far as I know will do any ECU)

Some folks use Ultimate Tunes.

I'm not tied to any shop. If asked would recommend any of the above based on what is required to be done.

If I have a bad experience I change shops and they loose my business, and sometimes my Skyline buddies will avoid the shop.

If any of these contributed to critical engine failure I take them to task over it.

Engine builds are best done interstate in my Opinion. Croydon's (CRD) built mine. Racepace I hear good things about. JEM is changing hands

Bolt on's and tuning as I said above is who you feel comfortable with.

Edited by Sinista32

Oh and I should add if you have an engine built get them to tune it after run in. Then there is no pointing of fingers if the worst happens within the warranty period.

My cars are not heavy hitters either. The closer you drive it to it's limits and beyond the closer you are to your next rebuild.

Shit happens and some drivers contribute greatly to the failure. No car is bullet proof. If you ring it's neck it will die.

Treat your car within tolerances and it will look after you.

Thanks for all replays. It gets boring in our a.c.t section so a bit of talk here and there keep it more interesting lol.

I'm no knocking any work shops I'm just very happy with the service and workmanship I received at Autotech. So that's why I'm recommending them.

I also had a little issue with my tune as it was a tad rich leaving black up the back side of my car. Ed booked me in and had to stay back to 7.30 to chuck my car on the dyno and run over things again. He ended up dialing up more boost for me and checked through it all.

He did all this for me free of charge as he said he wanted to keep me happy. I don't know to many tuners like that.

I am Just a happy customer.

He did all this for me free of charge as he said he wanted to keep me happy. I don't know to many tuners like that.

I am Just a happy customer.

I basically had the same experience at Trojan.

Free Retune to achieve what I originally wanted, but due to some issues, didn't get first time round.

Subject covered many times and there is a sticky at the top of this forum. http://www.skylinesaustralia.com/forums/topic/41527-where-to-get-skyline-serviced/page-35

Boils down to choose who you feel comfortable with. Each one of these shops below had/has issues with vehicles that have shit themselves.

Certain shops have ECU Tuning preferences. For me at the moment:

Ed (Autotech) tunes my 34GTT - Nistune (Autronics & Nistune dealer)

Glen (ESP) tunes my 32 GTR - Haltech (Haltech & Vipec's)

John (Trojan) does all my mechanical - coz I trust him, he's experienced and VERY helpful. (Jake does the Tuning and as far as I know will do any ECU)

Some folks use Ultimate Tunes.

I'm not tied to any shop. If asked would recommend any of the above based on what is required to be done.

If I have a bad experience I change shops and they loose my business, and sometimes my Skyline buddies will avoid the shop.

If any of these contributed to critical engine failure I take them to task over it.

Engine builds are best done interstate in my Opinion. Croydon's (CRD) built mine. Racepace I hear good things about. JEM is changing hands

Bolt on's and tuning as I said above is who you feel comfortable with.

I've used crd when I was living in Sydney as well. The are prob one of the workshops I'd highly recommend.

I basically had the same experience at Trojan.

Free Retune to achieve what I originally wanted, but due to some issues, didn't get first time round.

Trojan are very good no one knows skylines like. John in Canberra. He was who I originally wanted to tune my car but it's like a 4 weeks waiting list which was inconvenient for me.

I basically had the same experience at Trojan.

Free Retune to achieve what I originally wanted, but due to some issues, didn't get first time round.

Myself included. Wielded a few parts on my car as well as a few other things he did free of charge(:

I also use Bob Jane in Belco for tyres - extremely nice staff and always give discounts :)

I would say trojan as well. John is the guru of skylines.

Have always went to him, yes his prices are sometime a little too high but he is the only person i trust

Also he has a dyno on the floor which is so good for cars which are too low

My brothers R34 with Apexi SAFC was tuned my him.

Edited by 5hiv

All tuners will have horror stories and good things said aobut them.

Get quotes from the major shops in canberra

and go from there based on price vs customer service. Some shops that treat 1 person really well might fk over someone else. So just go on your gut feeling.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
    • So, a bit of a side trip, but one that might be interesting for people with JDM cars and japanese head units. I know @Pac previously posted about a carplay/android auto adapter he installed which used the AUX input, and @V35_Paul put in one of the Tesla style units that replace both screens. The option I went with was a Lsait LLT-YF-VER5.87_2 (https://www.alibaba.com/product-detail/Lsailt-8GB-Android-Multimedia-Interface-for_1601187633672.html). Price was $1,150 for a single unit although they are much cheaper if you are willing to buy 2....$857ea. Make you you get the version 2 not version 1, it is faster and has a better UI - this is the manufacturer listing: http://www.lsailt.com/product/348.html. BTW if you've never bought from Alibaba before, don't be concerned....these guys can't stay in business unless they are responsive, ship fast etc, they were excellent (probably faster shipping than most local places) So, this was my task for a lazy Sat afternoon....looks complex but was all done in a few hours (it probably helps that I had some of it apart before so it was a bit familiar). I also decided to add a HD USB drive recorded at the same time and the unit also supports an aftermarket reverse cam (if you don't want to retain factory) and also AV in and HDMI out It looks much worse than it is, in fact in was genuinely all plug and play (no custom wiring at all). This video was pretty good (skipped a few steps), unfortunately they are an Aussie seller but no longer sell this unit (I guess Carplay/AA adapters are easier to install and much cheaper) https://www.youtube.com/watch?v=T5hJfYOB8Dg
×
×
  • Create New...