Jump to content
SAU Community

[Vic] R33 240Rwkw Package Stripping Whole Car


Recommended Posts

hi sau long story short had a perfect r33 running done heaps of mods some dick ran into me back end.. so i decide to buy another shell and slap everything in but now i cbs to hot lol got over it .. so letting evereything go at good price.

would like to sell whole package first if can, if cant i will be stripping it down

so for sale package is

x1 shell with full interior no running gear quater panel has dent, other wise shell is still good it can be register not viv or written off status. no regeo atm ran out like 2months ago. i paid 600

x1 shell rear ended comes with everything you need to put in the good shell. engine is still very healthy n box hardly drivin odo has only 85..000 khms

engine mods

tein coilovers full adjustable

inismo injectors i think there 600cc? yellow ones

rsr 3inch dumb pipe + cat back

garret gt25/35 very responsive

nistune ecu cost me 1.4k for tune and z32 ecu

z32 air flow meter

gready aloy intake not just a straight pipe goes skinny to big to pod

original simmons wheels not bbs18x10 hard to find you can say rare? came off a r33 gtr wrap in achiles 90% tread has gutter rash but no buckle

brand new clutch done like 2,000khms cant remember brand but i spend total 1.2k light fly wheel and 6puck clutch

body kit r33 gtr front bar side rear pods got damage

full sound system spent 800

thats about it im sure there is more cant remember

3.5k with everything i have listed above engine gearbox all mods beside wheels i want 1.8k for wheels

so for 3.5k you can have yourself a modify skyline 240rwkw

alot of work to be done but good for project car or can be register price is nego

so basically you just need to swap everything over simple as that

contact van 0405 555 237

if i cant get a offer for whole packege in next 2 weeks will be selling indivisual parts

western surburb

  • Like 1
Link to comment
Share on other sites

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • Agreed with the rest. Also at least based on my own research, there are no readily available stock or close-to-stock RB20Neo maps that you could download and use as a base were you to buy a complete standalone ECU, and the regular 20DET maps don't really work well so you'd need to take it to a tuner if you have no experience. I installed an AEM V2 on my 20Neo+T and had lots of headaches until I got it to run and idle properly but I've yet to remap it fully. You have to start building up your timing and fuel maps entirely from the ground up; even the ones for a 25 didn't work at all.
    • Got some decent progress after work yesterday and also today. Got the ECU all wired and passenger side interior all back together. Kept the wiring up nice and high to avoid people standing on it. Got the surge tank relays rewired and tidied up the pump wiring and cut a hole to bring the cables through.  I found a spare USB cable I had lying around so I decided to cut it up and see if I could use it for my CAN 1 bus. Turned out one of the pins I needed was to the shield of the cable so i cut it up and desoldered it and resoldered to the correct pins.  Had the issue with the powersteering hose hitting the A/C compressor and fan shroud. I pulled the bracket off and modified it to remove the front mounting point which now clears it all. Will keep an eye on it to see if theres any signs of fouling once it's up and running.
    • That's some good input mate. Nice.
    • So today I went well outside my comfort zone (again) to replace my valve cover gasket.  I have had a big leak over the exhaust leading to a lot of smoke and smell every time I drove it. The leak was in the rear driver's corner.  The job wasn't hard as such, just a bit finicky and time consuming.  The old gasket was rock hard and broken right where the leak was.  The leaky corner had so much sitting oil in it.  The good news to my amateur eyes was no buildup or sludge under the cover. It all looked fairly nice in there.   I haven't started it yet. I ran out of light and body when putting the coils and injector loom back in. Probs only 30min left for the morning.  I was so nervous putting the cover back on, I must have lifted it 5 times to make sure the gasket was still seated properly. God it's going to be nice to be leak free and not make other traffic light queuers think my car is about to explode.
    • Gave the Mazda it's first wash, it will need some clay, a light compound, and polish polish to remove a few swirl marks, but that will be a job for when I have a full day to get my DA polisher action on
×
×
  • Create New...