Jump to content
SAU Community

Recommended Posts

the other day i uped the boost on my r33 so that it know runs around 10-11 psi but dont know if this model has a boost cut or i have some bad fuel, or maybe time for some knew plug. once it gets boost of 10-11 it splutters and pops through the exhaust. the plugs have done 25000 kms and the fuel im using is mobil.

Link to comment
https://www.sau.com.au/forums/topic/43586-boost-problem/
Share on other sites

sorry as far as i know they have a boost cut for over boosting, I ran 14psi and no drama's, my car did suffer a broken land on piston 6, just when i bought it, because of a failing fuel pump, I found out after the rebuild that the fuel pressure dropped away under load. this was before I did any mods to it. a new 044 and she was a steady pressure again.

Link to comment
https://www.sau.com.au/forums/topic/43586-boost-problem/#findComment-891084
Share on other sites

Cav its your plugs, I just went through the same prob last weekend, car loosing power like spark or fuel cutting at anything higher than 9psi.

I replaced the plugs from fairly new NGK's to Double Platinum Autolits $90 all up and was advised by two different GTR specialist one online in N.Z skylinesdownunder forum to gap them to .66 So I took them as close as I could to that and guess what, it bloody worked, boost is fine all the way to 12psi - not game to take any further till I get a front mount.

Link to comment
https://www.sau.com.au/forums/topic/43586-boost-problem/#findComment-894992
Share on other sites

i found iridiums to be shite in my S13 ... soon as i upped the boost with an EBC it started missing. took the iridiums out and put in just your normal cheapy plugs that are like 12$ a set and it worked a treat. id say find out what is the cheap copper alternative to your plugs (NGK brand still though) and put some of them in at the same gap of .75-.8. for $12 it cant hurt to see if it is just crappy plugs.

yeah u need to dyno your car with a fuel pressure guage to test the fuel pressure. however, if you are upping your boost, it is a sensible option to upgrade your fuel pump anyway, especially if your planning to run the higher boost all the time and more power in the future. an 044 intank replacement is usually a good bet.

if it still has issues and you want to go for a Malpassi pressure regulator, do that after you've done the fuel pump. the Malpassi wont do much good if you have a stock fuel pump coz the pump will struggle to keep up the increased pressure anyway. i had a misfire in my DR30 skyline, changed plugs and leads, reset ecu, upgraded fuel pump, and still had a misfire at around 1bar. after fitting a Malpassi Rising Rate regulator the misfire is now gone.

try plug changing and see how you go to start with though!

Link to comment
https://www.sau.com.au/forums/topic/43586-boost-problem/#findComment-902830
Share on other sites

guys i have changed the plugs with a set of ngk cheapies and still the same. got my mates to watch the ass of it and it is blowing raw fuel out the exhaust. do they have trouble with the coils, maybe one doesnt like the increased boost (extra load). it doesnt play up till high in the revs 5000-6000 rpm. i can run 10-11 psi low in the revs with no trouble.

Link to comment
https://www.sau.com.au/forums/topic/43586-boost-problem/#findComment-909192
Share on other sites

  • 3 months later...
sorry dude havent sorted the problem yet, am thinking coils, or an after market computer its got me stuffed need to get it to someone whos playing with them all the time. i might sell it yet, that will fix it.

luckily it seems it was just my plugs...I hope you get yours all worked out though. Good luck!

Link to comment
https://www.sau.com.au/forums/topic/43586-boost-problem/#findComment-1054385
Share on other sites

guys i have changed the plugs with a set of ngk cheapies and still the same. got my mates to watch the ass of it and it is blowing raw fuel out the exhaust. do they have trouble with the coils, maybe one doesnt like the increased boost (extra load). it doesnt play up till high in the revs 5000-6000 rpm. i can run 10-11 psi low in the revs with no trouble.

Sounds like a fuel problem dumping too much fuel in and choking on it if its coming out the exhaust as a liquid :uhh: - SAFC ll can fix this.

Could be the coil packs, you'll need to tape them up with duct tape. Because the spark can ark out the side which results in the plug not getting the full spark. Do you run the black cover ontop of your coils - Saying Nissan 2498cc etc... ?

Hope that helps.

Link to comment
https://www.sau.com.au/forums/topic/43586-boost-problem/#findComment-1054433
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Are you suggesting that the kit did a cheap and nasty job of just jamming the wheel in between other things and caused the misalignment? I mean, we normally do this with an integrated crank trigger wheel, not something bodged on. It's not 1995 any more.
    • I mean, given the number of BMWs you own their tolerance for improper torque is rather low. The number of torque + angle spec bolts and non-reusable bolts in one is nuts.
    • Atmospheric vent requires something that doesn't use a MAF for load. You would need a standalone ECU for that.
    • Hey all,   I’ve got an RB25 with a trigger kit that includes a crank wheel, and I’ve hit a wall trying to sort a timing belt tracking issue. The belt either rides right on the edge of the cam/crank pulleys or walks slightly forward once the engine starts. It tracks okay-ish for a moment, then creeps right to the edge—and honestly, it’s stressing me out.   I’ve spent hours removing and reinstalling the belt, double-checking everything:   Tensioner setup is good, checked multiple times Idler pulley and washers are all in the correct places Followed the RB25 timing procedure step-by-step     The only thing I changed was the rear crank washer—I swapped the OEM one for a Neato version, and it made things worse. The belt now sits even more forward than before. I’m beginning to think the crank trigger wheel itself (from the trigger kit) is the issue—poor design or slightly off dimensions.   What’s strange is that with the previous belt setup, it actually ran fine for a couple of years—around 4,000 to 5,000 miles, even with hard driving and high RPMs. But even then, the belt was always riding right on the edge, and I know that’s not ideal or safe long term.   At this point, I’m debating whether to:   Machine a few mm off the crank trigger wheel to bring it back in line, or Replace it entirely with a better-designed unit     Only thing is, I already have the Cherry Hall sensors, bracket, etc.—I just want to replace the wheel only, not the entire kit. Anyone know a brand or supplier that sells just the crank trigger wheel on its own?   Would really appreciate any feedback—especially from anyone who’s run into this exact issue and found a reliable fix.   Thanks in advance.
    • Hi...a little refresh. Is Nistune gonna be enough to run BoV? Or do i need some proper ECU? 
×
×
  • Create New...