Jump to content
SAU Community

Recommended Posts

Hi guys, finally got my dream car (after like 5 years lol) a 1995 r33 gtst (highflowed turbo, 92,000kms etc, clean car!) and I have been doing alot of audio work on my other cars, and since i have alot of stuff left over, thought I might aswell do a nice system for this car, but nothing over the top! I was thinking about putting my fusion reactor 900w 4channel amp in to run the front and rear speakers, and maybe put my fusion reactor 12' sub with 800w mono in the boot too. Im gonna go and get some nice 6" (if thats what I can fit in the doors) speakers and 6x9's for the parcel shelf. What I wanted to know, is has anyone taken out the factory amp and replaced it with an aftermarket amp? the car atm has some ancient double din headdeck which im gonna change too. if you guys can take the time to explain where the factory amp is and how to replace with an aftermarket one would be awesome!! in the boot, whatever cover that would have covered where the back of the seats are and the battery is missing, so getting into that sort of area is simple. thanks alot guys!

Link to comment
https://www.sau.com.au/forums/topic/436756-r33-gtst-aftermarket-audio/
Share on other sites

  • 4 weeks later...

If I was you I wouldn't bother with the 6x9s if your putting in a sub. Get a good set of 6" 3 ways for rear and a good set of splits for the front.

Also if your putting in new amps I wouldn't even worry about the stock one. Its not going to interfere cause nothing will be running off it.

But that is me, good luck with it

Hey mate. Dont really want a sub in may car au, i was bored one day so grabbed some 6x9 spacers and chucked in 3 way 6x9 on the parcel shelf and put in good 6" 3 ways in the doors. Sound good, once i put my amp in will hopefully sound alot better lol!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • @Haggerty this is your red flag. In MAP based ECU's the Manifold pressure X RPM calculation is how the engine knows it is actually...running/going through ANY load. You are confusing the term 'base map' with your base VE/Fuel table. When most people say 'base map' they mean the stock entire tune shipped with the ECU, hopefully aimed at a specific car/setup to use as a base for beginning to tune your specific car. Haltech has a lot of documentation (or at least they used to, I expect it to be better now). Read it voraciously.
    • I saw you mention this earlier and it raised a red flag, but I couldn't believe it was real. Yes, the vacuum signal should vary. It is the one and only load signal from the engine to the ECU, and it MUST vary. It is either not connected or is badly f**ked up in some way.
    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
×
×
  • Create New...