Jump to content
SAU Community

A31 Rb20 Ecu

Tassiecefiro
 Share

Recommended Posts

Tassiecefiro Newbie

Tassiecefiro

Posted
Posted

gday boy and girls

Im in need of a little bit of help and a definite answer to my problem.

I have purchsed an 1988 a31 cefiro rb20det and im in need for a ecu.

The problem is im not sure i can use any rb20 ecu or it has to be a cefiro one.

Any help would be a appreciated

cheers alex

Link to comment
https://www.sau.com.au/forums/topic/437255-a31-rb20-ecu/
Share on other sites
  • 1 month later...
jamind Enthusiast

jamind

Posted
Posted

Hey If your not sorted yet, I have the meanest RB20/25DET ECU fitteted with an Apet Maifacture on a dyno for my A31 Cefiro, it will blow your mind, i have all the specs on it and garrentee maximum power output for a standered motor, All i had done to my RB20DET was a pod filter, straight through exhaust to the rear performance muffler and mine has a RB33GTR Manul gearbox, It owes me $400 nz $ if you or anyone else wants there mild manure RB to turn into a scary monster its plug and start playing rough, Jamind 0212968943 nz, or maill me

Link to comment
https://www.sau.com.au/forums/topic/437255-a31-rb20-ecu/#findComment-7196506
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • JC71
      gauge needle removal

      By JC71 · Posted

      I have done a lot of research before posting here and on gtruk forum. couldn't find anything. I have my gauges all part except the needle itself. the needle has a extremely small hole in the center, but the shaft going to the needle is extremely small and appears to have nothing to index it either. doesn't seem strong enough to simple pry or pull without damaging something. Already tried the old spoon trick on a extra triple meter I have from a gtt, but no luck. the center cap comes off easily but the hole in the meter face plate aren't big enough to get over the needle itself. figured this would be my best place to find someone who might have actually removed theirs. wonder if there is some type of small pin press tool to push the pin in while pulling the needle base off.
    • Roy
      A Boy's Love For His Rb20

      By Roy · Posted

      Ok...its taking me long enough to finally do this.  Feck financial security...heart disease will get me soon enough anyway So welcome to the garage..."Clem" Belsil80 has been running a 370Z in Super TT series. So after entering with him in last years Winton 300 i figured I  need my own car. Seems SAU Vic race cars need to be yellow....{tick} Reckon with enough motor i will be able to make up for the lack of talent and stay ahead of the 370Z... but the LS powered S13 and E36s are a ways up the road Aim is to have a car that doesnt stop or turn but has a bit of shed built motor with jam...maybe some cream  First step is getting this ex drift car log booked I am keeping faithful silver car. As the road-club car gets upgrades the race car wil get the sloppy seconds
    • GTSBoy
      gauge needle removal

      By GTSBoy · Posted

      Assuming that they will come off without damage at all.... i would have thought just pull straight up off the spindle with a something or other than can reach underneath. Have you searched for youtube vids of people doing similar on R34s or any other Nissan from the same vintage? They should be the same technique, in all likelihhood.
    • GTSBoy
      Wheel refurb?

      By GTSBoy · Posted

      Keeping in mind that sandblasting is really aggressive on softer metals like cast alloy, and you can do damage that you might regret. For trash wheels, not a problem. For wheels with value/scarcity issues, etc.... perhaps a less aggressive media is a better choice?
    • GTSBoy
      R-chassis INNER tie rod torque spec?

      By GTSBoy · Posted

      Don't get all high and mighty. Experienced spanner wielders know exactly what effort is required to release an Oof.
×
×
  • Create New...