Jump to content
SAU Community

Recommended Posts

Alrite guys, Kinda new to the forum.

Im located in the US and currently close to finish my rb26 build on my 240sx.

want to see what u guys think and what i might be missing.

Rb26 head:

Supertech vavve guides,springs,retainers

greddy 1.2mm HG and arp head bolts

tomei type b cams

spool oil drain

Stock bore rb26 block

JE 8:3:1 pistons

eagle rods

Arp main studs, acl bearings

collared crank, n1 oil pump with spool gears

9.8qts sump from skyengineering

Raw brokerage twin scroll manigold

precision 6262 bb t4 .84 divided housing

twin tial mv-s

Fuel ID 1000cc injectors

-atm single walbro in tank(enough?)

Haltech plug in

tomei 1.5mm oil restrictor

goal 600hp

What fuel pump you guys recommend?

Max rpm rexommended for this setup?

Also have ross tuff metal jacket damper

Edited by silvianc
Link to comment
https://www.sau.com.au/forums/topic/437626-r32-gtr-600hp-mod-list-complete/
Share on other sites

Are we talking 600hp at the motor or at the treads here?

For 600 at the fly then your setup is fine.

600 at the wheels, I think you need a surge tank with maybe 2 walbro's. but it is very dependant on what fuel you will be running to know what your fuel setup should be.

I would've gone with id 2000's

Are we talking 600hp at the motor or at the treads here?

For 600 at the fly then your setup is fine.

600 at the wheels, I think you need a surge tank with maybe 2 walbro's. but it is very dependant on what fuel you will be running to know what your fuel setup should be.

I would've gone with id 2000's

600 hp at the wheel. Using methanol injection. I dont have access to e85 in my area. Was thinking to add a inline pump

I would suggest that on the dyno, your fuel system will probably pass. However if you intend to do any track work, you will need a surge tank. I use a 500lph walbro as a lift pump and a bosch 044 from the surge tank to the engine.

  • 1 year later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...