Jump to content
SAU Community

Recommended Posts

Units like this need to mounted on the windscreen - not a big deal these days with every other vehicle having mobile phone and/or GPS units mounted there aswell. There are more advanced ones that use sensors on the dash/back window/front grill, but the unit hides away.

You can modify a radar detector to become a detector-detector - this is what the police use and it provides a signal direction too. Most decent units have a shut-off that once it acknowledges that it is being tracked, it will stop detecting to avoid being identified. This obviously only works if there are other cars around. If you're by yourself, it won't matter.

It will pick up mobile radar no problem as they tend to operate continuously and as someone said, the signals bounce off anything/everything. Speed cameras are a strange one - some operate continuously (easy detection), some operate sporadically so you might think its a false signal and ignore the alarm (shopfront motion sensors for automatic sliding doors can set some models off). Lasers are difficult - they hardly reflect off other vehicles, and if it gets pointed at you, you'll be warned as your speed is recorded.

This is all just general knowledge to answer some questions, not specific to the model being sold here.

Just curious, would radar detectors detect Highway Patrol cars jsut driving around?

Reason I ask is that I've been told some HWP cars have radars in their car to detect speed and is mroe or less constantly switched on. Any truth in that?

  • 3 weeks later...

After all of this talk ,are these things any good?

Or, if caught you are in more trouble than just the speeding ticket????

Is there a product out there that gives us a fighting chance if we slip over the limit, without being fined for having a radar detector in our car.

If they have to put up signs saying there is a radar speed detector up ahead , why are we not allowed to have something to detect them ??????

Before you shoot me down, "do not speed" and then "no problem" shit it is hard to stay within a 5k limit with a modern car where 1 or 2MM on the peddle is about 5 kph :w00t:

I have done lots of dumb driving over my life in cars that should not have been on the road and today would be scrapped , F, cable brakes were fun :w00t: the car could go twice as fast than it could stop :stupid:

I do 3500kms per week, I use one and cannot recommend them highly enough, yes they will go off at certain business/servos. yes the police with a handheld need to be locked onto your car for it 2 pickup laser alert, yes it will pickup highway patrol cars with there radar turned on before u see them and yes it will pickup flash for cashes parked on side of road. good luck with sale, good price :)

i just got a speeding fine, he said his laser showed i was speeding, so my question is does this unit tell me if a cop has a radar with a laser before i get in range of it?

Uhh, no.. by definition if you're not "in range" then how is the detector supposed to detect the radar or laser signal? a signal has to actually been seen by the device to be detected. with the laser speed measuring devices cops use today, you will have only ~1 to 2 seconds to drop your speed if you're speeding before they lock in the detected speed, in other words not enough time. Another approach would be to attempt to "jam" the signal by diffusing the laser with noise on the same wavelength buying you another 4-5 seconds to slow down... but not all of these have success in actually working as advertised, and are also illegal. Also note that most detectors are easily detected by police scanners because they emit a signal which can be identified - the only one i know of that claims is not detectable is the Bell XR/STi.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...