Jump to content
SAU Community

Advice On Instrument Switch \ Button Identification Pls

Rockit

By Rockit,
in V Series (V35, V36, V37 & Infiniti)

 Share

Recommended Posts

Rockit Explorer

Rockit

Posted
Posted

This is in relation to an '03, auto, premium model. I have conducted an unsuccessful search, also have a G35 handbook, but am still non the wiser.

On the console in close proximity the the transmission change lever, there is a rectangular switch showing Power, A\T and Snow. I assume the central position means Auto transmission and is for non specific driving mode; Power ?? - am using that presently, and then Snow allows for slippage in such conditions.

The other that has me puzzled is the small circular 2 position push in button down below the right of the steering wheel. In small white lettering, it has AUTO1 on it.

Thanks

Nightcrawler Grand Master

Nightcrawler

Posted
Posted

This is what I have worked out.

Power setting holds the car in each gear longer and downshifts earlier.

A/T is normal.

Snow is for snow - it turns the cars power down to less than 50% and turns up the slip sensitivity.

The auto1 button may be for auto fold-in mirrors?

damangm Contributor

damangm

Posted
Posted

I'm pretty sure I have the same model. The round button on mine activates the auto mirror dip when in reverse. And the switch to the left of the steering wheel has 3 positions. One manual mirrors folded in. One manual folded out. And one auto fold in when locking the car by remote.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Nightmare_mistress_R33
      CD009 RB Conversion

      By Nightmare_mistress_R33 路 Posted

      Yep that is correct. It allows you to adjust the short throw range from what I can tell
    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin 路 Posted

      Car has been running great, I've put about 300km's of break in time on it. First thing that stands out with properly sealing rings is no more noticeable crankcase smell coming out of my catch can. This may seem insignificant, but the constant smell while driving around was infuriating. It's also nice to see my oil level remain stable. Two new issues have developed that I only noticed this weekend though. There's a very noticeable driveline vibration past 100kmh. I only noticed it now as I've been babying it under 100kmh in the backroads. This comes as no surprise as I'm running a one-piece shaft, and I paid zero attention to my driveshaft angle when I put everything back in. I also have a fair bit of voltage drop on hot starts. The starter audibly is forcing. No issues on cold start though. I must not have removed all the paint under my main block ground during assembly. I'll try and take care of both those issues this week once the kids are asleep.  I also received all the parts I was missing for my direct port setup. I will hopefully have pictures of that up soon. I'm hoping to get back on the dyno the week of June 30th as I'll be on vacation. I'm confident I should be able to make north of 500rwkw on pump gas and WMI. I'll go back again later this summer with E98, but I want to confirm my ethanol content sensor is working properly first. I've never seen it read anything but 11%. This makes sense for our 10% ethanol content pump gas here, but I would expect the occasional movement between fill ups. 
    • jez NF
      The Evolution Of "night Fury"

      By jez NF 路 Posted

      75% complete. Will now need to get a new axle with 5x114.3 hubs and then figure out how to customize some mudguards for it once the wheels are on.
    • jez NF
      The Evolution Of "night Fury"

      By jez NF 路 Posted

      Trailer prep is underway... Lined up the wheel to get a rough indication of how it would sit Then removed all the bits (as far as possible) and gave the frame a light sand and quick lick of paint   Then added some carpet
    • JC71
      gauge needle removal

      By JC71 路 Posted

      okay, so I figured this out, removed needles and reinstalled after swapping the gauge face on my triple gauge for my ER34, all work and look good. I tried to do the same for the main cluster, but the main cluster gauge faces are dished, the replacement gauge face are flat, so due to the dish in the org face ,mounting backing plate (clear) and depth of the needle, the flat gauge face will not work. I notice that R34 gtr gauges are flat, appears to be different clear backing plate that aren't dished. are these available, or what have others done to install flat gauge faces?
脳
脳
  • Create New...