Jump to content
SAU Community

Rb25 Vct Camgear Bolt, Too Far Out Need Replacement

walky01

By walky01,
in Engines & Forced Induction

 Share

Recommended Posts

walky01 Enthusiast

walky01

Posted
Posted

hey guys, i recently posted up why my VCT was leaking, bought all parts and now it seems like my Bolt holding the VCT camgear in is out too much, the washer looks very thick, not like a normal flat washer, is that normal? the bolt sticks out so much that i cant put the VCT cover plate spring and 4 little bots on. an help appreciated !

Dose Pipe Sutututu Grand Master

Dose Pipe Sutututu

Posted
Posted

if you jiggle it you will feel there's a groove it goes into, I suggest you pull off the timing belt to get in into place

once it goes into place then hold the cam with a wrench and torque up the nut.. it will then sit flush and allow you to put the spring/cover/seal on

Ben C34 Grand Master

Ben C34

Posted
Posted

Because you have different cams I would not activate vct until you know you can. Cams with more overlap cant run vct or else the inlet and exhaust valves could hit.

Obviously you need to fix the leak though but dont plug in the solenoid until you are sure its ok.

walky01 Enthusiast

walky01

Posted
  • Author
Posted

they are standard rb25 cams reground, the engine has gone through two guys here, dondenaso (i think thats how you say it) and Skit_r31 both same setup.... not sure if you have seen them on here before, in the n/a section.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      Dose's Sometimes DIY and Pay Someone Home & Boat Improvement Thread

      By Dose Pipe Sutututu · Posted

      Wife wanted basket things in the wardrobe in our temporary house. Thought about ripping our the wardrobe and fitting the entire IKEA set, but it's a temporary house and we want to move in a few years. So IKEA advertises this as a 50cm unit, however the actually basket and rails measure 46cm wide. Only issue was depth, IKEA stuff is quite deep, where as the builder special junk is super shallow at less than 40cm. Send it, chopped the rails, then offset the mounting holes, job done, happy wife, less shit scattered all over the bedroom. Did the same to the other side too. Also drove the Skyline shit box today, dropped off oil at Supercheap Auto. I didn't realise they only now take max 2x bottles per visit. I visited 2x Supercheap Autos.  
    • Kinkstaah
      Strange issue RB25DET wont start

      By Kinkstaah · Posted

      I've seen similar actually in my situation. You never know what tables are attempted to be used when the car thinks it's -99C or +200C. The fail state is not usually that extreme but you know what I mean - it was in my case though! This is where being able to read all the sensors is useful cause you see this stuff really quickly.
    • Kinkstaah
      First time Skyline owner

      By Kinkstaah · Posted

      The above is very important. However as long as you keep timing relatively low, it's plausible to make your own knock ears and plausible to learn to tune with a modern ECU that can do wideband O2 correction like a boost controller. I mean if you only have one viable road to even drive the car on, learning to tinker to this level may be worth doing given you can't do much else with the car...?
    • Kinkstaah
      Chris' Toyota Mark ii JZX110

      By Kinkstaah · Posted

      I find the fact that the rear plate has to be bent inwards at the rear not so bad: but the front is just awful: It's like come on. (these are my very old, now retired/turned in plates) TBH it is a lot of money to fix a minor issue, the fact I said "I'll never really spend the money on doing this" is why people ended up buying them as a gift for a 'car guy' who can be hard to shop for.. for car guy things.
    • GTSBoy
      Chris' Toyota Mark ii JZX110

      By GTSBoy · Posted

      I just bent the ends of my premo plates. It even went through Regency like that after the engine conversion and the inspector (a great bloke!) just squinted his eyes and said "I didn't see that". Plates, and how they look, are just something that have zero importance to me.
×
×
  • Create New...