Jump to content
SAU Community

Which Clutch For 500Kw At The Rear Wheels?

eXquiSit
 Share

Recommended Posts

eXquiSit Mentor

eXquiSit

Posted
Posted

i was previously thinking about rebuilding my twin plate pull nismo clutch so i put up a thread on that and everyone offered suggestions so i called the shops up for their opinion

jim berry suggested i go with a single plate pull clutch which would hold the power with increase in clamping force

npc and direct could rebuild my twin plate

these options cost between 1100-1600ish

i believe i can also get a new os giken twin for around $2000 and then either use the push/pull converter or do a bellhousing swap

just was wondering what everyones opinion is on which route i should take

car is a weekend car and will go cruising etc but in saying that, i can live with a 'race' clutch with heavier pedal and bitey pick up point

XKLABA Grand Master

XKLABA

Posted
Posted

What car ? 500kw in a GTS-t is massively different to 500kw in a GTR

GTS-t rebuild your twin plate, if its shot

GTR go a hi-torque triple plate, which you can do if you have the Exedy "Nismo" twin by rebuilding it with triple plate centres

GTRPSI Mentor

GTRPSI

Posted
Posted

We went Jim Berry for less than you quoted, 5700Lbs clamp single plate, 5 or 6 puck for 600Kw in a GTR with a 26/30 street/drag build.

Jim has a few 9 second and quicker cars running them without issues.

Talk to him about your needs, driving style and power/torque levels, let him know what you will be doing with the car and listen to his suggestion.

The man knows his stuff, just be prepared to spend at least an hour on the phone with him, one thing his not short of is customer care.....

eXquiSit Mentor

eXquiSit

Posted
  • Author
Posted (edited)

  • GTRPSI: yea i spoke briefly with him as i know he is always busy and i didnt want to waste his time as i wasnt sure if i would buy his clutch or not. youre not wrong though bout customer service!

with that clamping load, how is the pedal feel?? extremely heavy?

do you know what friction material is in yours? and what is the take off like?

i dont flat change or dump/kick the clutch at all

through a kazz 2 way and 19x10.5 rear wheels and i believe 245/35/19s

before the clutch slip, i had no traction issues at all in 2nd and above once the tyres were warm

Edited by eXquiSit
GTRPSI Mentor

GTRPSI

Posted
Posted (edited)

Carbonetics friction.

We are getting ready to fit it, we just ballanced the pressure plate and flywheel, the clutch plate has a sprung center.

We made it clear to Jim that the car had to still be streetable, albeit rarely, our concern was holding up at the 1/4 mile, as mentioned he has made a few of these for street driven GTRs in the 9's and they are holding up well.

However one thing you need to consider or pass onto Jim is how much power your intending to push through it and how you will drive it.

If he advises a lower clamp load, go with it, we have a 5700 Lbs pressure plate, after bed in he said it will settle at 5400 Lbs, im currently modifying our crank main thrust bearing for extra oiling to help with the higher clamp loads we will be putting on the mains thrust.

Ideally with these higher powered builds and high clamp load plates you want a dog box, clutch to only be used on take off.

Lower clamping loads means you wont have to mod your thrust bearing, but the issue is with high tourque you cannot run a normal box, you could try but i dont know for how long it would hold up with those sorts power figures, going by others id say you better start looking for a stronger gear box, its the next weak link......

Edited by GTRPSI
eXquiSit Mentor

eXquiSit

Posted
  • Author
Posted

yea i am doing my best not to abuse the box by quick shifting, clutch kicking, burnouts, etc.

regarding clamp loads, if it is a twin plate, it shouldnt need as high a clamp load to hold the same torque right?

Carbonetics friction.

We are getting ready to fit it, we just ballanced the pressure plate and flywheel, the clutch plate has a sprung center.

We made it clear to Jim that the car had to still be streetable, albeit rarely, our concern was holding up at the 1/4 mile, as mentioned he has made a few of these for street driven GTRs in the 9's and they are holding up well.

However one thing you need to consider or pass onto Jim is how much power your intending to push through it and how you will drive it.

If he advises a lower clamp load, go with it, we have a 5700 Lbs pressure plate, after bed in he said it will settle at 5400 Lbs, im currently modifying our crank main thrust bearing for extra oiling to help with the higher clamp loads we will be putting on the mains thrust.

Ideally with these higher powered builds and high clamp load plates you want a dog box, clutch to only be used on take off.

Lower clamping loads means you wont have to mod your thrust bearing, but the issue is with high tourque you cannot run a normal box, you could try but i dont know for how long it would hold up with those sorts power figures, going by others id say you better start looking for a stronger gear box, its the next weak link......

XKLABA Grand Master

XKLABA

Posted
Posted

yea i am doing my best not to abuse the box by quick shifting, clutch kicking, burnouts, etc.

regarding clamp loads, if it is a twin plate, it shouldnt need as high a clamp load to hold the same torque right?

That's right as it has twice the friction surface area and some depending on the clutch plate JB uses

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Matt Z
      SAU NSW - Archies Flame Grille Meet & Cruise to Kurnell

      By Matt Z · Posted

      Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
    • Ozdavroz
      WTAC 2025

      By Ozdavroz · Posted

      Yeah good luck out there! Will be good to see a mighty GTST going harder than the GTRs
    • bcozican
      WTAC 2025

      By bcozican · Posted

      i will be there 😁
    • patrickxdf12
      Squeaking clutch/throw out bearing

      By patrickxdf12 · Posted

      Hello!  i just finished manual swaping my r34 skyline with a r33 rb20de box(RB71C)box  When the car is running it squeaks crazy loud and it was smoking from the gearbox area. The gearbox is fine it was tested. The clutch slave cylinder seems like it doesn't fully releases the clutch. I want to ask if this noise is from the throw out bearing or could it be the clutch assembly or disk att.xFliq87Gzw6kImKBVqDebXkj0fBqymk0JaYeP3_3SlM.mp4
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
×
×
  • Create New...