Jump to content
SAU Community

Recommended Posts

I'm changing my pads and having massive dramas now. The other side went perfectly well, and I'm now stuck on the front left.

I can't seem to compress one of the pistons at all. Is it possible for these to seize up or something? The other three pistons are pushed right back (I used a c clamp, as I have done with many cars in the past).

While I'm at it I also noticed brake fluid seeping from the crack where the two halves of the caliper join - Could this be resolved by tightening the bolts that join the two halves together or is that a no-no?

Thanks.

post-133052-0-32643200-1394097672_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/440175-brake-problems/
Share on other sites

Yep one of your pistons sounds like its seized. There are a few things you can do:

1: Crack the bleeder nipple & try & compress it (temp fix till you fix the weep, see step 2).

2: Get a rebuild kit & overhaul both calipers

3: Get two GOOD second hand calipers & fit them.

Link to comment
https://www.sau.com.au/forums/topic/440175-brake-problems/#findComment-7220081
Share on other sites

Agree with the above. The leaking from the joint is uncommon. Typically you just do the piston seals during a rebuild as the other stuff doesnt tend to fail, and its better not to disturb it if you dont have too. Of course in this case you would have to split the calliper and replace those seals too.

Tightening the bolts may help a little as a bandaid, but since the pistons stuffed too you really need to give it some more attention

Link to comment
https://www.sau.com.au/forums/topic/440175-brake-problems/#findComment-7220095
Share on other sites

So a local brake shop quoted anywhere from 180-220 per side, depending on condition of pistons. Looks like I'll be buying second hand :|

Possible you end up with the same problem though! In saying that, if it was my car that calliper would be in the bin as you should never shortcut on brakes!

Link to comment
https://www.sau.com.au/forums/topic/440175-brake-problems/#findComment-7220995
Share on other sites

If your located in a capital city, then I'd HIGHLY recommend a company named Hallite for the seals for the 2 halves that don't come in rebuild kits. They stock an enormous range of all compounds & sizes of seals, o-rings etc

www.hallite.com

And for different types of compounds (also for anyone reading this):

www.sealanddesign.com

Link to comment
https://www.sau.com.au/forums/topic/440175-brake-problems/#findComment-7221459
Share on other sites

Its a simple as piss job to do yourself.

Seal kit... http://www.ebay.com.au/itm/NISSAN-Skyline-Sumitomo-4-Piston-BRAKE-SEAL-REBUILD-KIT-Front-Disc-Brake-Caliper-/131114109959?pt=AU_Car_Parts_Accessories&hash=item1e87028c07

Piston if needed.... http://www.ebay.com.au/itm/NISSAN-Skyline-300ZX-200SX-Sumitomo-4-Pot-BRAKE-PISTON-Front-Disc-Brake-Calipers-/131113002258?pt=AU_Car_Parts_Accessories&hash=item1e86f1a512

If its leaking from the join, did you seperate the 2 halves? There is supposed to be a oring in there and your not supposed to seperate the caliper halves.

The bolts that join them are torque to yeild and not supposed to be touched......you cannot get new bolts but you could source a oring from a general pursose pack of rings.

Edited by GTRPSI
Link to comment
https://www.sau.com.au/forums/topic/440175-brake-problems/#findComment-7222146
Share on other sites

Thats interesting Pete.

Being torque to yield bolts, that probably explains why they aren't in rebuild kits.

Are kits available through Nissan? I'd imagine the bolts would come in a genuine kit.

Any torque to yield bolts shouldn't be reused, as they are stretched to near breaking point the first time they are torqued. Try it a second time around & they will 'soften up' (lose tension as you get near the max torque) & fail.

USUALLY any bolt that has a torque requirement that is in degrees of rotation (angle torque) will be a torque to yield.

Those types of bolts are specially made for specific applications, & you won't find them aftermarket. If you knew the tensile strength, you'd get close though.....

Link to comment
https://www.sau.com.au/forums/topic/440175-brake-problems/#findComment-7222685
Share on other sites

Nah didn't try to separate the two halves, nor tighten the bolts that join them - I could tell that wouldn't stop the leak anyway. Once I noticed it was leaking I just left it alone and based on advice given above, decided to just grab a used pair. I would happily attempt a rebuild if it was just the seized piston but I don't want to deal with splitting them open and whatever. I'm a bit surprised they (both fronts) leaked there actually. Have worked on lots of older cars with this design and never seen leaks there but anyway.

Turns out r33 parts are plentiful...probably easier than sourcing parts for my gf's fairlane ghia actually

Edited by mistermeena
Link to comment
https://www.sau.com.au/forums/topic/440175-brake-problems/#findComment-7222806
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Food for thought, the stock oil filter thread is a 3/4-16 UNF, which has an ID of about 10 to 12mm (according to ChatGPT lol). Now compare than to an 10AN, which has an ID of about 14mm (Raceworks is 14.2mm, Speed flow is 14.27mm).  
    • Yep, totally get that. However hooking in for Generator back up is only a few hundred bucks for the wiring. You could put a couple of those in (for different circuits explicitly) and run a couple of baby generators. Bonus, you can balance them across different circuits, and now have backups in your backup. I'm looking at buying places that won't even have water etc, and I don't mind the idea of getting off the electric grid either, even with everything you've said. This country already has enough power outages that even the mains grid isn't that reliable anymore. I do agree though on spending a bit more to get better gear, and to add some extra redundancy in to the system too.
    • You can set hard reserves on your battery system, and it can't be discharged past that.  
    • That sounds like an excellent idea. But total self-sufficiency means exactly that. You have no-one else to blame when your system faults out and you have no power for a week or two while it gets fixed. You'd have to go the whole hog and get a diesel genny and all the switchover gear, to get you through such times. And, despite the fact that over 20 years, my system has been pretty reliable**, I have seen so many inverter explosions (or less dramatic deaths), panel and roof JB fires, and so on, over that time, to know that the stuff is the same as any other bulk Chinese manufactured stuff. The failure rate is well above zero - both on the equipment and on behalf of the meth addled installation labour force. And then..... warranty and means of redress against the supplier you bought the gear from. Best I can tell is that only a handful of solar companies are still around within 5 years of starting their advertising pitch. They disappear and phoenix like crazy. So, as per 1st paragraph, I suspect the only way to is go balls deep and spend maybe 2-3 times as much as you might think, so that you have every base covered. Plus, know and understand your gear intimately, so you can diagnose problems, sort them out yourself, etc, etc. Plus, probably have to consider upgrading various parts as the years pass, to maintain compatibility with newer stuff, performance and reliability, etc, etc. Whereas, remaining attached to the grid has an ongoing cost that keeps going up even if you use bugger all power from it. But it does provide the fallback in case of the worst case with your own gear. You either pay up front or as you go, I suspect.
    • Add more solar panels to the array. Call the electricity company and tell them you're moving out... Live off grid electric wise
×
×
  • Create New...