Jump to content
SAU Community

idiot...

LOW25T

By LOW25T,
in General Maintenance

 Share

Recommended Posts

Guest two.06l

Guest two.06l

Posted
Posted
Ummm, i accidently snapped one of the wheel studs after changing my brake pads, is it safe to drive around in temporarily (with the remaining 4 studs), untill i get it fixed???

think about it this way 1/5 of the studs is 2/5 more dangerous, drive it with a 3/5 less throttle in 4/5 of a week to get it fixed before your car becomes 5/5 of the scenery.

Link to comment
https://www.sau.com.au/forums/topic/44081-idiot/#findComment-900767
Share on other sites
[WLDCRD] Mentor

[WLDCRD]

Posted
Posted

well, i guess it could depend on the condition of the other 4. I did the same thing once and i actually got pulled over and got a defect for it (amongst others) albeit it was a canary yellow V8 commodore which stood out like dogs balls haha Safety-wise, its probably not the best idea as the wheel could potentially fall off (worse case scenario) but if you are desperate like i was, you can as long as you dont do anything stupid. Best advice is to get it fixed asap.

Link to comment
https://www.sau.com.au/forums/topic/44081-idiot/#findComment-900773
Share on other sites
[WLDCRD] Mentor

[WLDCRD]

Posted
Posted

yeah i got mine welded on....but it snapped off again later. I must be too strong haha make sure if you get new ones they are the right length....cos my one ended up being longer than the others and the nut didnt fit. Luckily i had 50million of the buggers lying around. Its no big drama and it shouldnt cost you much. If you just twisted it off the hub thingy, you can reuse your original bolt.

Link to comment
https://www.sau.com.au/forums/topic/44081-idiot/#findComment-900801
Share on other sites
predator Grand Master

predator

Posted
Posted

one less won't kill you..

my other car i found out only had 3 studs on each wheel (and it only had 4 to start with).. and i've been driving like that since i got it for around 15,000km with no probs. If the others are done tightly i don't think the wheel is going to fall off.

But yeah, get it fixed if possible :D

Link to comment
https://www.sau.com.au/forums/topic/44081-idiot/#findComment-901429
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • Dose Pipe Sutututu
      What brakes on R34 GTT(Europe)

      By Dose Pipe Sutututu · Posted

      Pads for R32 GTS-t, R32 GT-R non V-Spec (Sumitomo), R33 GTS-t and R34 GT-t are all interchangeable. R34 GT uses a 2x piston caliper, hence it didn't fit.
    • soviet_merlin
      WGNC34 - floor mats

      By soviet_merlin · Posted

      Checked with amayama and nope, the full S2 manual set is not available anymore. Unsurprising, but still disappointing as the ? on availability gave a glimmer of hope.
    • joshuaho96
      Tomei gasket

      By joshuaho96 · Posted

      I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
×
×
  • Create New...