Jump to content
SAU Community

How Much Boost To Run My 6266'd Rb30

G37Sam

By G37Sam,
in Engines & Forced Induction

 Share

Recommended Posts

G37Sam Collaborator

G37Sam

Posted
Posted

Hello guys,

I have a built RB30 with a 26 head and a PTE6266, I only have access to 98RON pump fuel.

I am currently pushing it to just under 1.6 bar with no pinging but am itching to push it even further. What do you guys think? Would a low 8's Static CR take 1.8 bar on 98 pump fuel?

Any feedback/experience would be appreciated :)

Cheers,

Sam

Link to comment
https://www.sau.com.au/forums/topic/441590-how-much-boost-to-run-my-6266d-rb30/
Share on other sites
XKLABA Grand Master

XKLABA

Posted
Posted

There are so many variables that the only way to know is throw it on the dyno and see

I built a 2630 with twin GT-RSs and 9.5:1 static comp on E85 and I only expected to run 24psi and so far we're up to 28, went 30 but the spark gets blown out, but going from 26 to 28 it picked up 25hp at all 4, when we sort the spark issue then we will try 30 and see what happens, if it picks up another 20-25 HP we'll try 32 and so on till it no longer makes decent gains or get to high of a knock level

Boost doesn't kill engines poor tuning and preignition does

  • 7 months later...
G37Sam Collaborator

G37Sam

Posted
  • Author
Posted

There are so many variables that the only way to know is throw it on the dyno and see

I built a 2630 with twin GT-RSs and 9.5:1 static comp on E85 and I only expected to run 24psi and so far we're up to 28, went 30 but the spark gets blown out, but going from 26 to 28 it picked up 25hp at all 4, when we sort the spark issue then we will try 30 and see what happens, if it picks up another 20-25 HP we'll try 32 and so on till it no longer makes decent gains or get to high of a knock level

Boost doesn't kill engines poor tuning and preignition does

That is true, but you're blessed with E85. I'm stuck with pump fuel that was why I wanted to see what would be a safe limit.

what power is it making with the 6266 at 1.6bar?

Depends on the dyno really. Mine maxed out at 615whp at 1.6bar. Posted a dyno sheet on RB30 thread.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      Ok thanks..that was my second question if i can somehow bypass this even with Nistune(that is all i have right now...aparat from stock ECU. So with some aftemarket it can by "bypassed" or make it work?  I know there is Link or Haltech (mainly used). We have ECUmaster here so i will gather some info about it.
    • GTSBoy
      Boost cut after swap(RB25DET NEO) R34

      By GTSBoy · Posted

      Yes. You will need to get the original boost sensor and wire it in. That is.... if you plan to use a stock ECU - even a Nistuned ECU. The Nissan ECU will not operate correctly without it connected. And yes, it will do annoying stuff like you are experiencing. You will almost certainly be better off with some aftermarket ECU, than trying to hunt down rare sensors.
    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      Ok so ABS/TCS is "not" the problem. Yeah i know now about the ABS with Nistune(i told that to the Nistune guy) but iam not 100% why or why i dont have ABS. ABS cube is in the engine (always has been) but i had braked couple of times rly hard and brakes just locked and scream. Does all Skylines have ABS cube? That boost sensor https://www.sau.com.au/forums/topic/367633-wtb-r34-gtt-turbo-pressure-sensor-pics-inside/ Is this it? I need to ask but i have a picture of engine bay and i do not see that (100% is not in that place) If i do not have this the car can do what mine is?(cutting around 4000 rpm) Here is the pic of my engine bay(only one i have) BUT i think i dont have that cuz loom was used from my RB20DE NEO and i know (obviously) that it does not have boost control or any wire to that...) so maybe that is the problem? (i dont know for 100% if that car where the engine is from had that)...but i dont have the loom from that
    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      I'm with you here. It's either loom has an issue, OR, injectors are not functioning properly. It could even be they're just constantly dribbling, hence the wet, but not firing.
    • Duncan
      S1 rb25/s14 starting problem

      By Duncan · Posted

      Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
×
×
  • Create New...