Jump to content
SAU Community

Recommended Posts

Parting out my S13 project car as I will no longer have time to complete it or drive it so everything must go.

S13 origin type2 50mm rear over fenders as new condition three tiny pilot holes drilled on each fender for test fitting $300

S13 Dmax Style 40mm front fenders slight chip damage from shipping $230

S13/180sx Apexi Power FC ECU + Hand controller Serial no. PFC SR2015 020-0601 $700

SR20 Kelway steam pipe manifold external gate suits T3 flanged turbos brand new only test fitted $550

S13/180sx Blacktop SR20DET has 98,XXX kms on engine minus turbo,manifold,ECU (PFC can be negotiated with price) included KTS extended baffled trap door sump, engine loom, starter motor $1600

Trust/Greddy rocker arm stoppers brand new $100

S14 Front lower control arms pair $120
S14 Front knuckles and hubs has NISMO extended wheel studs $150
5 Stud rear hubs pair $120
R32 rear handbrake shoes pair $80 dust shield slightly bent on edges.
R33 hand brake cables $50

OR

Complete 5-stud conversion
$450

S13/180sx 5sp manual gearbox with shifter will needs new shifter boot $450
Extreme clutch puk clutch used condition still 70% $150
SR20DET flywheel $50
S13/180sx Manual master cylinder $30
S13/180sx clutch pedal $30
S13/180sx Brake pedal $30
S13/180sx manual tail shaft $80

OR

Complete manual conversion for S13/180sx including clutch
Including clutch $ 750
Excluding clutch $550

S13/180sx/R32 rear traction arms pair $40 or $20 each x2
S13/180sx/R32 rear camber arm pair $40 or $20 each x2
S13/180sx/R32 rear lower control arm $60 or $30 each x2

S13 track only shell sun roof model
Non rolling included is s13 power steering rack, and cross member all windows still intact and doors, fuel tank.
Rear panels cut and welded for rear over fenders.
Only has epoxy black primer.
Has tubbed front.
$400
Only holding onto to shell for 3weeks then it will be scrapped get in before it goes to the junk yard.

Location northern suburbs
Additional pics can be sent upon request
Contact Anthony
0466111592

post-38352-0-27633000-1396879140_thumb.jpgpost-38352-0-19241700-1396879149_thumb.jpgpost-38352-0-44395600-1396879159_thumb.jpgpost-38352-0-08266200-1396879165_thumb.jpgpost-38352-0-10552100-1396879173_thumb.jpgpost-38352-0-00726100-1396879180_thumb.jpgpost-38352-0-55119100-1396879192_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
    • Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
×
×
  • Create New...