Jump to content
SAU Community

Recommended Posts

I have continually had trouble getting DTV reception in my coupe with my Alpine TV tuner. The reason is more than likely that the stick on antenna is on the top of the windscreen but placed where the tinting is.

I have purchased 2 x HiTV antennas which I am going to place inside of the bumper bars. I was wondering if anyone has done this before & if it is difficult to do? I am presuming that both of the bumper bars have to come off completely. I also need to run the antenna wires back into the cabin & don't know the easiest way to do this. Can anyone offer me some advice?

I was also wondering if anyone has used the HiTV pure 4 (or3) TV tuner? If so comments would be appreciated :no:

I believe with antennas it's better to have them higher rather than lower, the aim is to have line of sight.

A great example are houses in a valley, see how they have massive antennas and they usually all point in the same direction? It's to get line of sight and they aim at the transmitter because house TV antennas are directional.

  • Like 1

I have to agree that higher would be better but without having them visible I don't have a great deal of options. I would still like to know if anyone has mounted then this way and how hard it is to get the bumpers off?

A workshop manual will probably show you have to remove the bumpers and as for running cabling just use existing grommets in the firewall but if you want more examples just do a quick "the google" search and see if other people have installed antennas in their bumpers.

OK, height is not the key to reception, LOS (line of sight) is, height is for better LOS. I really advise against putting them in the bumper. I could be wrong, if these conditions are met if you live in a relatively flat area with minimal trees, minimal high rise buildings and the transmitter is your neighbor you might be lucky.

Give it a go, but I'm just trying to save you the work of fail.

Cars are not the best for TV. My antennas are in my rear quarter panel windows (wagon) I get a couple of digital channels but as soon as a van or car parks near me that's it... no more reception.

I also thought that installing the antennas into the bumpers was a bit strange but according to HiTv this is the way to go. I guess I will just have to install them & see how I go.

Line of sight is better, but you aren't going to get line of sight very often from the windscreen anyway. And if you have metalized tint, it is going to kill the signal anyway. With the TV channel reallocation, they are all moving to a lower channel anyway which will help to reduce the 'line of sight' issue. It won't help for obstructions like hills or large buildings, but trees and smaller objects will be less of an issue.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
×
×
  • Create New...