Jump to content
SAU Community

Advice Needed...

32mqdness

By 32mqdness,
in Queensland

 Share

Recommended Posts

32mqdness Apprentice

32mqdness

Posted
Posted

I have a R32 GTS-t and have bought a second set of rims for the car,

Front is 18x9.5 and rear is 18x11

haven't tried to fit the rears yet but doesn't take much to know they won't fit without rolling the f#@k out of the guards,

before i start rolling the guards just wanted to know if anyone know where i can get a set of over guards from for the 32. Haven't been able to find any in old and need it before friday to get car ready for QR.

Link to comment
https://www.sau.com.au/forums/topic/441892-advice-needed/
Share on other sites
C4a0s Proficient

C4a0s

Posted
Posted

I have a R32 GTS-t and have bought a second set of rims for the car,

Front is 18x9.5 and rear is 18x11

haven't tried to fit the rears yet but doesn't take much to know they won't fit without rolling the f#@k out of the guards,

before i start rolling the guards just wanted to know if anyone know where i can get a set of over guards from for the 32. Haven't been able to find any in old and need it before friday to get car ready for QR.

nismo has them for the 32 i believe... but definitely cant get them in time for friday...

Link to comment
https://www.sau.com.au/forums/topic/441892-advice-needed/#findComment-7258577
Share on other sites
MagicMikeZ32 Veteran

MagicMikeZ32

Posted
Posted

You will find legal issues with such wide wheels under the increased wheel track section of the ADR's. Flares will just point this out to the po-po, which is why I have not installed my 18x13's with flares. Just safer to wait for the widebody :(

If you need to do something by Friday, go down to clark rubber and get some black rubber and stick it on ;)

Link to comment
https://www.sau.com.au/forums/topic/441892-advice-needed/#findComment-7259453
Share on other sites
  • 4 weeks later...
32mqdness Apprentice

32mqdness

Posted
  • Author
Posted

After a fair bit of stuffing around I got some of these, just need to figure out how to get the original guards flared out enough underneath to fit those 18x10's properly. (I tried a guard roller but it doesn't roll any further than they already are)

Link to comment
https://www.sau.com.au/forums/topic/441892-advice-needed/#findComment-7283202
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Starting again

      By Kinkstaah · Posted

      Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
    • Duncan
      R32 GT-R: 4WD Light Turns On After Bumps – Code 19 (ETS Motor) But No Issues Found

      By Duncan · Posted

      Agreed, and in particular the earth strap that should go from the subframe to the chassis but it often broken or left off. There is a section in the R32 workshop manual you can follow for troubleshooting if you don't see anything suspicious, and depending where you are (there is no location on your user profile) you should be able to get your hands on a second hand replacement unit still if needed
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      Yeah they mention as a R34 for 2.5 Turbo...but then again thos "small" were also for R34 by that different site. But i look into it and that 310mm EBC is for R34 GTT. And by those you linked the specs are the same 🙂    EDIT: I found these on one site here: DBA 4000 series T3 DBA42304S They are 310mm...and it says are for R34GTT...are there good? EDIT2: ok they have pads too.  What "color" should i get for street use? I dont want/need some noisy ones...(and if they are not that dusty that is good too)
    • Marek
      WGNC34 - floor mats

      By Marek · Posted

      Yeah, shame. Maybe  driver's carpet is available 🙏. I am waiting for both amayama and nangun to confirm.
×
×
  • Create New...