Jump to content
SAU Community

Recommended Posts

hi all,

well i got defected today, the following "faults" were found.

-bov under bonnet

-wheels and rims 3inch oversize

-no clearance between body and top of tyres

-not comply with 100mm clearance

-no tyre placcard

-oversize exhaust

-loose wires under passenger floor mat.

can someone whos been through this tell me will i get a fine for each and every point listed above? As "no clearance b/w body and top of tyres" and "not comply 100mm clearance" are the same thing! ie too low!

and oversize exhaust?! WTF is that?! isnt it the noise level not the size of the pipe that matters?

It says i have to clear it via a FULL INSPECTION. Whats the deal here in NSW- if i fix the problems on the current defect, will they just go over the car and send me home with another dozen things to fix?

If thats the case then ill just drive it back to SA and do it there, at least i have all the tools/parts there.

cheers

Link to comment
https://www.sau.com.au/forums/topic/44232-defect-helpadvise/
Share on other sites

1. BOV is illegal, no two ways about it

2. Technically, if the wheels are more than an inch wider or larger than stock, they require an engineers sign off to be deemed safe and accapetable

3. There is no clearance rule in terms of tyres & guards to my knowledge, other than no part of the wheel or tyre should foul/scrub on any part of the inner guard or suspension. If it does, and there are marks to prove it, then there are grounds for a defect

4. You need to have a tyre placard, the fact you dont have one will more than likely cause the officer to further doubt the legality of your wheels and tyres, particularly when they probably have no idea what size the car came with factory

5. If the officer suspects your exhaust is too big or too loud, they can send you to the EPA for testing to ensure your exhaust complies with the DB limit. To clear it either replace your exhaust with a standard system for testing or try and quieten your existing exhaust down to a suitable level.

6. Loose wires? Odd one - police normally wouldnt go to such effort when defecting so obviously it just wasnt your day. Try and clean the wires up

The end :)

Link to comment
https://www.sau.com.au/forums/topic/44232-defect-helpadvise/#findComment-903974
Share on other sites

i didnt exactly get defected for doing nothing, i was having some fun at the time which drew attention to myself.

The defect category is "MINOR" and says it must be cleared at an AIS (authorised inspection station)

-What/Where is an AIS? Is it like a registered workshop/garage? or is it a full RTA depot place?

-Also where would i get a tyre placcard?! They mustve left it off after the respray.

-And again, does anyone know if the defects are subject to a fine?!

Link to comment
https://www.sau.com.au/forums/topic/44232-defect-helpadvise/#findComment-904401
Share on other sites

Yup give your local RTA a call and they will be able to give you the address of some local work shops to clear it for you. From memory the cost is $20 for them to sight your vehicle and pass it, no fine (from memory a fine would be stated on the defect notice).

Just fix the minor things and then rock up with a case of beer in the passenger seat and see how you go. Theirs nothing proving that you didn't change things 'back' to what they currently are after you left the AIS.

:D

Link to comment
https://www.sau.com.au/forums/topic/44232-defect-helpadvise/#findComment-904614
Share on other sites

if they haven't given you fines on the spot then you are pretty much all clear...

also, give the rta a call, because when i got defected and still had qld rego i called both the cops & the rta to see how i could get it cleared and both of them said that they couldn't clear the defect cos it was a qld registered car.....so i called qld transport & they said that they couldn't do anything because the defect was issued by nsw police

so i took it to the AIS that is currently in my garage & engineered it myself......read: i took off the canary & never heard from the cops/rta about it again

Link to comment
https://www.sau.com.au/forums/topic/44232-defect-helpadvise/#findComment-905175
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Working through possible solutions of converting my mechanical speedo.    Anyone know what type of speedo sensor the factory r34 gtr getrag has ? what the output is ? I assume its not a VSS and more a voltage like earlier speedo sensors ? Can an ECU read it ?  
    • roof rail delete used to be a thing, they were made locally for a while too
    • I can get more photos of it here soon and I plan to make a thread detailing the process. I received the car this way and it sorely needs refinishing. That is probably the most appealing photo of it. Up close it is fading, cracked, and needs to be re-glued. Depending on their condition I'm on the fence between refinishing or making a new set.  Another angle hiding the pimples and razor pumps  
    • According to this thread the RS4V with build plate RC40 comes with the R200 diff @ 4.083 ratio as well (mine has said RC40 denotation). We may need to check if the axle stubs are the same pattern as well. The auto subframes have longer axles. However I think yours being a later Series 2 as well, we should have the same bolt pattern for the diff stubs. Unless your upgraded rear also has upgraded axles. Either way, I would not be opposed to pulling the covers to check so I can inspect that  fancy rear core  Also I don't have HICAS. I don't believe that should change things but I hope the people here with heaps more experience than me can correct me if I'm wrong   Let me know if you want to attempt to make this work and I can get some pictures of mine from under the car. 
    • It's not that straightforward. For example I have had this code because my ignitor/power transistor wires were unplugged. It knows something is wrong but has no idea what it means. If you want to actually diagnose this I recommend following the service manual flowchart for code 21. Ohm out the harness, coilpacks, inspect the ECU, etc. And again, it's entirely possible for there to be no problem at all but if you're running a different coilpack it'll trigger the code because it doesn't like what it sees.
×
×
  • Create New...