Jump to content
SAU Community

New Plugs And Coils Car Not Running Right

polzin

By polzin,
in Engines & Forced Induction

 Share

Recommended Posts

polzin Enthusiast

polzin

Posted
Posted

ok so i put new coils on last week and worked awesome still had some spark breaking down issues but not as bad today i put in new plugs BPR5ES gap down to 0.7 now i put it all back together and fire it up it seems to be not firing on 3cyl or 6cyl i double check loose connections now i am lost :/

Ben C34 Grand Master

Ben C34

Posted
Posted

And after rereading your post, you disturbed the loom and it got worse, so that seems to point to the loom.

Is 5 heat range stock? That's a pretty hot plug. I use 7 heat range, most guys say go with 6 or 7. Not 5.

Ben C34 Grand Master

Ben C34

Posted
Posted

how i check them was pull each connetor of one at time to here to miss

That's the smart way to do it.

You can then swap coils and see if the miss moves, letting you pinpoint coil or loom.

polzin Enthusiast

polzin

Posted
  • Author
Posted

i got them off a member off here there is spark in cyl 3 going to test cyl6 after work i got a feeling it may be a boost leak but i think maybe the coil loom is on its way out so ill just pull it all apart again tomoz and see how i go with it all just a sill question say if i a plug the loom wrong like had one swapped around will this cause a miss?

MJTru Mentor

MJTru

Posted
Posted

What you might want to do is a compression test on all cylinder. After that's Ok. Take out all the coil packs and unplug them along with the injector harness. Then remove the CAS sensor and test by plugging in one coil at a time from any cylinder. Let's say number one. Turn the CAS sensor clockwise with the ignition key on holding the coil with spark plug in it . You will see the spark plug fire. That ecu channel would be good and coil and plug would be good as well if spark is present. Repeat this on all coil and ecu channels. You can use this method for injectors, but a noid light would be safer and easier. I have had this happen to me and it was the plug on the ecu.

Hope it helps mate.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Starting again

      By Kinkstaah · Posted

      Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
    • Duncan
      R32 GT-R: 4WD Light Turns On After Bumps – Code 19 (ETS Motor) But No Issues Found

      By Duncan · Posted

      Agreed, and in particular the earth strap that should go from the subframe to the chassis but it often broken or left off. There is a section in the R32 workshop manual you can follow for troubleshooting if you don't see anything suspicious, and depending where you are (there is no location on your user profile) you should be able to get your hands on a second hand replacement unit still if needed
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      Yeah they mention as a R34 for 2.5 Turbo...but then again thos "small" were also for R34 by that different site. But i look into it and that 310mm EBC is for R34 GTT. And by those you linked the specs are the same 🙂    EDIT: I found these on one site here: DBA 4000 series T3 DBA42304S They are 310mm...and it says are for R34GTT...are there good? EDIT2: ok they have pads too.  What "color" should i get for street use? I dont want/need some noisy ones...(and if they are not that dusty that is good too)
    • Marek
      WGNC34 - floor mats

      By Marek · Posted

      Yeah, shame. Maybe  driver's carpet is available 🙏. I am waiting for both amayama and nangun to confirm.
×
×
  • Create New...