Jump to content
SAU Community

Recommended Posts

Hey guys

Im looking at taking my wife's v35 head lights apart and painting the insides back and polishing up the lenses.

I have never done this before so any help would be great.

I plan on starting it on Friday night and finishing it by Sunday night as this is her daily car.

Does anyone have any suggestions with method? paint? what not to paint etc?

Any help would be much appreciated

Thanks

Kris

Link to comment
https://www.sau.com.au/forums/topic/443329-v35-headlight-modifications/
Share on other sites

I finished mine a few months ago, split the headlights painted surrounds and resealed. Fairly simple stuff, the mistake I made - and it was a huge mistake - was to try and clear coat the lights for more protection/shine. I'd watched some youtube videos of people clear coating with great success, apparently they wern't using acrylic. When I sprayed the lights they looked good for a few minits then they literaly melted! The fist milimeter or two of the light surface crazed like a turtle shell. I ended up sanding from 300 up to 2000 to get a clear lense again - literaly days of sanding and polishing.

Anyway, the process is all over the net, take out the screws (about 3 or 4 from memory), bang em in the oven and pry them appart (google the temps). The lights are made up of lots of pieces, so painting them is easy. If you want to get rid of the orange indicator you need to cut it out, I just wanted my lights back together at this stage. A full weekend is just enough time to do it right. I used auto paint for the satin black - no clear coat. I wouldn't try and polish the inside, it has some tight corners that would be virtualy impossible to do right.

IMG_1947_zps0c40b1f5.jpg

IMG_1946_zps40986c2c.jpg

IMG_1949_zps2e28ca57.jpg

cheers for the reply bud,

whats your lights like at night??? i see you painted most of the light black, looks great but i was worried about the lights not being bright enough coz they cant "reflect as much?

The reflector is separate, painting the surround doesn't effect the light output. If you look at the surround you will see that there is no surface that helps light output, they are just for looks. There is a separate section to the high beam light that is under the low beam tube (hard to explain) I didn't paint that. The early lights don't even have that part.

So, im gonna start taking the lights out tonight.

anyone have any suggestions on best way????

i knoe front bar has to come off, which is gonna be fun but anything else we should remove to amke it easier???

i ahve also tried googling the temperature we should use to take lights apart in oven but can see to find anyhing consistant

There are 4 bolts and wiring holding in the lights (also indicators in bar), once you drop the bar you will see them, one in the engine bay at the top, one in the side, 2 at the front.

Can be done by undoing the top and sides of the bar and pulling it forward, very high chance of scratching the paint unless you tape the sides... even then?

So, after a loooooong weekend the lights are finally done.

Took a lot longr than what i thought, being old lights the insides had a few cracks on them, i tried to repair them but just didnt look right, so cleaned them up and tarted again, ypu cant really see the cracks anyway once the lights back together.

Faitly simple process, but polishing the clear lenses took the longest, there was a film on the inside of one and it took about 4 hours to clean off.

Heres a few pics of how they turned out, will post a pic of them on the car soon once i have chance to take a better picc in the day time.

When prying them apart though i lost some of the glue, i had some sikiflex that i used to put on her roof spoiler so i used some of that. seems to be good s its been raining since sunday and no water in lights so very happy

post-107907-0-03098200-1401318194_thumb.jpg

post-107907-0-45228700-1401318197_thumb.jpg

post-107907-0-77762100-1401318199_thumb.jpg

post-107907-0-77222600-1401318201_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
×
×
  • Create New...