Jump to content
SAU Community

R33 Reverse Lights Not Working!

choombs

By choombs,
in General Maintenance

 Share

Recommended Posts

89CAL Grand Master

89CAL

Posted
Posted

Theres a plug in the engine bay, just in front of the fuse/relay box. It joins the gearbox harness to the rest of the car. Mine was dirty and my reverse lights sometimes went funny then all of a sudden stopped

R32Abuser Mentor

R32Abuser

Posted
Posted (edited)

Simplistically, I would imagine the following:

Switch at the g/box

globe at the rear of car

fuse in the engine bay

and wiring to join it all together...

If you've multi'd the switch (when closed!), checked that the globes actually light up under a power source, then there is only the the wiring and the fuse to check.

That being said, did you check the switch for continuity? I found with my box/switch (R33 RB25), the only way I could verify that the switch was good was using a test light and a mini 12V battery.

Multimeter did not display/sound continuity unless powered!

Edited by R32Abuser
Daniel_33 Collaborator

Daniel_33

Posted
Posted

My reverse lights work for a second when I put it into reverse then go off. Not sure what it is they used to work when I pulled and held the gear leaver back but now they only work for the second when I first put it into reverse. Any one had this before? Thanks

R32Abuser Mentor

R32Abuser

Posted
Posted (edited)

Locate - Yes.

Troubleshoot - depends on how mechanically/electrically minded you are!

There is a plug at the reverse switch (on the gearbox) and in the engine bay where it joins back into the wiring loom.

Ground - I'd have to take a look and the wiring diagram to see exactly where the circuit is grounding. Something I neither have the time or the patience for at this time of the night.

Edited by R32Abuser
R32Abuser Mentor

R32Abuser

Posted
Posted (edited)

After checking everything again, still couldn't find the fault >.

What did you "check" and how?

He also checked everything and still doesn't work. ....

Something isn't being checked correctly.

Agreed.

As I said above, I had issues testing the circuit without having reverse selected and powered. Otherwise I got nothing...

Edited by R32Abuser
89CAL Grand Master

89CAL

Posted
Posted

I've had the wiring diagram out

There is a plug at the tail-lights (obviously), a plug drivers side top front of boot (this may be out of sight inside the guard, I'm not real sure), the plug at the front which I mentioned before and then the plug at the switch on the gearbox

I cant find what fuse it is tee-ed off, but there are a fair few things powered off the same circuit like the de-fogger relay (rear window) so if thats working I dare say the power source is O.K.

Basically just need to test the switch, or bridge out the plug to eliminate the switch completely. Get the lights working without the switch and then you can see if the switch works. If you have power at the switch harness, then the earth is at the tail lights. If you have all the other lights + number plate lights then Earth is most likely not your problem, the Earth is common to all of them.

dyl33 Mentor

dyl33

Posted
Posted

OP has already said he has tested the switch and it is O.K.

My switch could test fine to, i could also wiggle the gear stick while in reverse and get reverse lights going for a few seconds. Was very weird new switch fixed it. No idea if that's OP problem. Just a thought

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Stringycheese
      Blue slip

      By Stringycheese · Posted

      Thanks for the response. This is an 04 EP3 Type R. JDM spec. Fairly certain they're just basic BC racing coils. I do plan to keep as the ride quality on stock I've been told is pretty meh given Sydney roads. If I were to go down that avenue, does NSW require them to be a certain spec (close to original) etc?
    • PranK
      Blue slip

      By PranK · Posted

      Should have asked what is the car?
    • PranK
      Blue slip

      By PranK · Posted

      I've had two super conflicting experiences with blue slips. My 30 year old E39 waltzed through with no issues but my brother in law was knocked back on 12 y/o 3 series due to wiper blades and some cracking in a control arm bush.  What kind of coil overs? Do you want to keep them after?  If it was me I'd get some dirt cheap shocks and springs from eBay or scumtree. Not ideal but will get you over the line and might even be less than $1k.
    • QB6SAGR
      Tein Circuit Master- rebuild worth it?

      By QB6SAGR · Posted

      Hey guys,  Way back when (about 15yrs plus), I picked up a beautiful set of Tein 'Super Racing Spec Circuit Master RE' coilovers from Russman. I have legit never fitted them to my car, as it was garaged indefinitely while i bought a house Yada Yada. They look brand new! Anyway its time to pick up where I left off, and have started doing some khanacross and am booked in for a hill climb next month. The car has some hard af Nismo shocks in ATM, which has me wanting to upgrade again, and now I am left wondering if it's worth having these teins rebuilt? I think they where an ok shock back then, but how do they compare to what's on the market now?  Shockworks/mca are 2800+, and I am sure they are great. But if I can have these rebuilt and be better than, say, a set of bc's for around the cost of bc's, I would be happy with the performance v cost trade off.  If they are considered outdated and rubbish these days, so be it, I'll put them on the shelf and be happy to look at the pretty green colour while I save for the SW/MCA option. Grateful for your thoughts on the matter, and suggestions on who could do the rebuild if it's a worthwhile pursuit.  cheers, Rowdy. 
    • TurboTapin
      Ethanol Content Sensor - Always at 11%?

      By TurboTapin · Posted

      I can't speak for the US, but for Canada as I mentioned above, all fuel gases contain ethanol. We have regulations for E5/E10/E15. Each province handles it differently but basically any fuel gases sold must be E10 and slowly increasing to E15 by a certain year. 
×
×
  • Create New...