Jump to content
SAU Community

Recommended Posts

Due to unforseen circumstances I have had to sell off parts from my uncompleted project.

Firstly the engine:

RB30DET

RB25DE stock head full reco with 110lb valve springs

RB30 block sonic checked and awd machined, with machining for tensioner pully relocation

CUSTOM side feed intake plenum with trumpets inside cost $1350

CP pistons 86.5mm

Spool Rods

ARP main, rod and head studs

NITTO OIL pump

NITTO crank collar

ROSS metal jacket balancer

NPC 10 inch clutch

TOMEI 1MM oil restrictor x 2

TOMEI SUMP baffle

HI OCTANE RACING awd SUMP adaptor.

NISMO engine mounts

6BOOST manifold

TIAL 60MM wastegate

BORG WARNER EFR 8374

DENSO 650CC low impedance injectors

TURBOSMART FPR800 with fuel pressure gauge

Custom Dual entry fuel rail

$700 of braided Teflon line for turbo oil feed, 2x water and 1x return.

YELLOW JACKET cool packs.

GTS4 AWD SUMP with 4.33 diff.

Engine is new! Has not been run yet! Looking for $16000.

Runs CP file back rings

ACL RACING big and mains bearings at .25

FULLY BALANCED ENGINE, engine pistons are also machine fitted to its specific bore and balanced accordingly. Machine work alone was $3500.

Also rebuilt r32gtr box so now 4th gear crunch $900

APEXI A.V.C.A.R $400

3INCH MAGNAFLOW 100 CELL CAT.$120

Walbro 040 $120

Fully rebuilt r33 GTST brake callipers full set $800 with rotors and new Lucas pads

Link to comment
https://www.sau.com.au/forums/topic/445561-rb30det-awd/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
    • Will this fit? but they are staggered set - RAYS 57DR SEMI GLOSS BLACK 18x8.5 +37 | 18x9.5 +38 5-114.3 STAGGERED SET   or If no go could just get a set 4's wheels of 18x8.5 +37 5-114.3 - would i run 8.5's 235s up front n 245's at the back if I do?   Thanks.        
    • Put a clamp on your return line. I have a feeling it's sucking air, and introducing bubbles to your fuel. With a lot of fuel, less problematic. I'd honestly be redoing all the lines in the tank and clamps on everything.   Also, you've given two different answers to the same question: Asked if being followed by the police you could get down to use the whole tank, you said yes you could, so long as you keep off boost. However, you then followed this up that free revving, it would also cause the issues. I'm doubting free revving is enough to make any noticeable boost on what is likely a decent sized turbo.   So now I have to ask, can you actually drive it lightly and use all the fuel, or does it break up even free revving? Also, have you put a fuel pressure gauge on it? Can you hear the pump change noise at all when you're having this issue?
×
×
  • Create New...