Jump to content
SAU Community

Recommended Posts

Hi all

Listing the below is for sale:

Bodykit stuff:

R32 - Frp Vertex Front Bar *new* - $250

R32 Frp vented Dmax bonnet - 2nd hand - has front cnr broken (but still attached will need to fibreglass fix, a small hole in back of one vent, has bonnet pins / holes - $150

R32 frp Dmax front guards + 15 - 2nd hand - have small cracks in them but pretty decent, been repaired before so are now thick frp most of the way through - $80

R32 4 door vertex side skirts - 2nd hand - been trimmed neatly front and rear to fit + clear tyres and small plam sized rough bit along one of them - $50

Suspension:

R32 Kazama front camber arms - 2nd hand good condition nothing wrong - $250

R32/ S13/14/ 15 Front Castor rods - Kazama - 2nd hand - good cond - $100

- Driftworks *new* - $200

Random:

Greddy Intercooler 600 x 300 - been bashed around a fair bit but still held 500+ hp + ally piping for rb high mount turbo + plaz plenum - $100

R32 brake calipers full set front and rear - have usable but nearly gone pads Freddo 2500 front and Project Mu D1 spec rear = $150

Ceffy Cross member - $50

Rear strut brace - Ally (blue ends silver middle) good cond - $50

R32 gtst coilpack harness suit rb20 / rb25 s1 coils - $75

If your looking for anything like above type stuff (not the little bit from the little bit over there in the back) ask as I may have it

Please contact me on 0411173970 or PM if interested or want pics.

Thanks. Laine

Edited by bcozican

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
×
×
  • Create New...