Jump to content
SAU Community

R33 Gtst Speedo Sensor Resistor Vaule

boostn0199

By boostn0199,
in General Maintenance

 Share

Recommended Posts

boostn0199 Grand Master

boostn0199

Posted
Posted

Anyone know the vaule resistor that the stock gtst cluster uses to convert the speedo signal going to the ecu? Ive binned the cluster and just want to keep running the speedo signal direct to the ecu and get the reading off the power fc but now it is reading to high as there is a resistor used in the cluster to correct.

boostn0199 Grand Master

boostn0199

Posted
  • Author
Posted (edited)

Can you play with the speedo signal with your ECU?

Ill see if I can find anything in the wiring diagram but dont recall any in the cluster

Dont think theres anytging ecu side muck around with it. On the wiring diagram shows ecu output to a resistor then to speed sensor now since originally the ecu gets the signal from cluster im assuming the resistor for correctiin would be there.

Might have to much around with a potentimeter see if i cand find the value.

Edited by boostn0199
89CAL Grand Master

89CAL

Posted
Posted

I can't find a resistor in my wiring diagram. Can I ask which diagram you are using?

I wasnt sure if you had a standard ECU or not. The Link ECU's allow you to modify the speed sensor input frequency to road speed, so if your speed is a little out on the ECU, you can adjust it to give true road speed

boostn0199 Grand Master

boostn0199

Posted
  • Author
Posted

I

I can't find a resistor in my wiring diagram. Can I ask which diagram you are using?

I wasnt sure if you had a standard ECU or not. The Link ECU's allow you to modify the speed sensor input frequency to road speed, so if your speed is a little out on the ECU, you can adjust it to give true road speed

I got power fc. This is the diagram ive seen it on, which one are you using?

http://www.sau.com.au/forums/uploads/post-2917-1129784245.jpg

89CAL Grand Master

89CAL

Posted
Posted

Ignore the resistor. It's just showing the sensor itself and how it is drawn. Bit decieving in that diagram, the one I have shows the speed sensor (as pictured, then wiring which goes through a plug on the way to the cluster

SpeedSensor_zpsdcee4377.jpg

boostn0199 Grand Master

boostn0199

Posted
  • Author
Posted

The cluster must alter the signal somehow because its reading 4times the speed wired directly to sensor now or either the ecu just takes the reading off the the std speedo gauge itself.

Have mucked around with resistors today added 1k but did not change anything.

89CAL Grand Master

89CAL

Posted
Posted

Odd the diagram shows nothing in the line between the sensor and the cluster. There is a VSS module inside the cluster that might alter the signal out

If you dont want the cluster, maybe you could pull it apart and have a look whats inside, then either add the same thing to the circuit or pull the VSS module out of the cluster and run it inline.

I wouldnt think it would be a resistor it needs in the circuit because as far as I know the ECU wants to see frequency, so pulses/second etc

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      GTR R34 Limp Mode

      By GTSBoy · Posted

      Has equal chance of cleaning an AFM and f**king an AFM. I think you can work out what happened. When the Hitachi ECU sees the AFM die and goes into the associated limp mode, then it will start and run just fine, because it ignores the AFM and just runs on idle maps that will do what it needs to get it going. But there is no proper load signal, so that's about all it can do. My suggestion? If you don't want to go full aftermaket ECU, then get some R35 GTR AFM cards and some housings to put them in, in the stock location, and Nistune the ECU. Better to do a good upgrade than just replace shitty 40 year old tech with the same 40 year old tech.
    • steven7270
      GTR R34 Limp Mode

      By steven7270 · Posted

      So my car was recently having trouble starting on initial crank, I would need to feather the gas for it to start up but besides that it would start and run fine. So I clicked the idle air control valve (with throttle body cleaner) and cleaned the MAF sensors (with MAF cleaner). The start up issue was fixed and now the car turns over without the assist of the throttle, but the car is in limp mode and wont rev past 2.5k RPM. From what I understand the IACV would not put the car in limp mode, so I am to believe it is the MAF sensors, but it was running fine before and now I cant get it out of limp mode. I cleaned the MAF made sure the o rings were seated properly. Made sure the cables were plugged in properly, the cables also both read the same voltage. Does anybody know why this is or what could be causing this or how to get it out of limp mode?
    • Dose Pipe Sutututu
      SAUNSW - Cruise - Albion Park Aviation Museum - 9th August

      By Dose Pipe Sutututu · Posted

      Ooo I might actually come and bring the kids, however will leave the shit box home and take the daily
    • PranK
      Rusty roof repair

      By PranK · Posted

      Thanks. Yeah I realised that there's no way I'd be able to cover the holes with the filler, it would just fall through. Thanks again @GTSBoy!
    • GTSBoy
      Rusty roof repair

      By GTSBoy · Posted

      That was the reason I asked. If you were going to be fully bodge spec, then that type of filler is the extreme bodge way to fill a large gap. But seeing as you're going to use glass sheet, I would only use that fibre reinforced filler if there are places that need a "bit more" after you've finished laying in the sheet. Which, ideally, you wouldn't. You might use a blob of it underneath the sheet, if you need to provide some support from under to keep the level of your sheet repair up as high as it needs to be, to minimise the amount of filler you need on top. Even though you're going bodge spec here, using glass instead of metal, the same rules apply wrt not having half inch deep filler on the top of the repair. Thick filler always ends up shitting the bed earlier than thin filler.
×
×
  • Create New...