Jump to content
SAU Community

Recommended Posts

Nitto oil pump brand new only test fitted to car $1100

RB30 series 2 block standard bore $200

CP forged pistons 20 thou oversized with the largest pins available capable of 2000hp (also comes with

standard size pins as well) suit rb30 $1000 brand new

Npc twin plate clutch suit r33 gtst and r32 gtr, only done 400km $1400

R33 r34 rear toe control arms harden rubber hardrace brand, brand new $120

Russ toffbond metal jacket balancer excellent condition $500 suit rb25

Cometic mlsr head gasket suit rb26 and rb30 brand new $170

Rb26 valley cover, timing cover and timing backing plate $250

Rb crank collar brand new $70

Arp rb30 main studs brand new $200

Arp rb25 head studs brand new $200

RB underdrive pulley kit (power steering, alternator, water pump) brand new blue in colour $75

Rb2530 tensioner idler and belt set up only fitted to engine $130

Nismo engine mounts r33 hicas $150

Dynamat bulk extreme kit $170

R33 power window arm with motor $50

H1 hid kit Chinese brand, brand new $25

Located North Brisbane Caboolture area

More parts to come, can sms pics if genuinely interested

Thanks, Matt 0498 188 451

Link to comment
https://www.sau.com.au/forums/topic/449432-lots-of-rb-performance-parts/
Share on other sites

  • 3 weeks later...
  • 2 weeks later...
  • 2 weeks later...


  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...