Jump to content
SAU Community

Recommended Posts

That's the idle air circuit, AAC and air reg connect here.

Cheers for that man, it had a hole melted in to it, i have taped it for the meanwhile. would a hole in it cause my car to run like crap?

Absolutely, you'll let unmetered air into the engine below boost, and let out tons of air on boost. Definitely would run like crap.

Ohh okay, because thats what it feels like its doing, its hitting 8 psi, but doesn't feel like its pulling at all. almost feels like its letting all the boost out somewhere. I have taped the hole really well until i get a replacement, but its still doing it.

Edited by rb25debt

What has been done to the black pipe that connects to that nipple?

That pipe connects (via the AAC and air reg) to the plenum so I doubt the engine would run unless the pipe has been blocked.

I followed it and its still hooked up to the plenum, it goes to a joiner that goes along the top of the back of the engine. The hole was melted by the external wastegate

So you're saying the hose end is open to atmosphere?

Under idle conditions, the throttle plate is effectively closed and the engine draws air via that black hose.

The AAC valve and the air reg are part of that system, which ends by connection to the plenum.

This means with an open hose, when idling the engine is eating unfiltered air and when under boost conditions, boost is escaping.

It's not too difficult to connect that hose to the "J" pipe as originally intended.

So you're saying the hose end is open to atmosphere?

Under idle conditions, the throttle plate is effectively closed and the engine draws air via that black hose.

The AAC valve and the air reg are part of that system, which ends by connection to the plenum.

This means with an open hose, when idling the engine is eating unfiltered air and when under boost conditions, boost is escaping.

It's not too difficult to connect that hose to the "J" pipe as originally intended.

Yea it's still connected to the correct place it just had a hole melted into it. i taped it for the mean while

I see, that's not so hard then.

As a temporary measure I'd cut the hose at the burned part and sleeve it with a piece of steel tube/hose clamps until you can buy a suitable replacement.

The hose has to take heat and boost so tape won't cut it.

Ahh good idea, yea i'll do that tomorrow, i also realized my bov isn't going off, it just compresser surges. as i said earlier it makes 8 psi boost but doesn't pull like it is. When i had the gate hooked up wrong and it was over boosting the bov was going off.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks for doing that Duncan! Makes you a good person in my books. We don't get kangaroos or wombats here. But we have bats and it's similar. AFAIK it's often the mums with a baby attached that get hit because they drop lower when starting from a tree. If you hit an animal, check on it. https://www.ifaw.org/au/resources/wildlife-rescue-app An app to get the closest wildlife rescue contact.
    • My dream is also to have a proper hoist, but I don't think it will ever happen. My quickjack is probably as close as I'll ever get, it really is very good though. 
    • Yeah we keep on in the dailies, it is pretty poor how many animals get hit and the driver leaves without checking....have saved a couple of little ones over the years. Bit of a gruesome job though, pouches generally need to be cut open because they are so tight and often the joey doesn't realise mum is gone so they are still locked onto the teat. I checked the modules in front of the DS wheel where an oil cooler should go.... There is the radar unit - that can go for race use) One of the 2 HX water pumps, the silver cylinder. That needs to be kept but might be able to be relocated But the bad news, the big computer mounted vertically in front of the wheel (blocking any potential air exit) is the electric steering computer. That is required until/unless i do a hydraulic steering conversion, and in CAD based modern car design it is not like I can just pop a big unit like that somewhere else (plus the loom would be too short anywhere else too). So, the passenger side is OK to clear out (just use a smaller washer reservoir, potentially elsewhere), but the DS no beuno
    • Well, all the best with the new camry It was interesting to hear about the UK process, it is generally a lot more streamlined here with a shipping agent looking after all the import side (noting the exact final price can still be a surprise.....) and I've used a few different brokers on the japan (or US) side, and never had any trouble with any of them....luck of the draw I guess. You mentioned you didn't get the auction sheet (understandable since you bought it from a dealer, not auction), but I always try and get hold of that because they are pretty thorough. I've imported 2x R grade vehicles over the years and both were fine, repairs in Japan are pretty thorough compared to here in Oz.
    • BTW I measured the jack I have, it is 70mm at the saddle but you only have about 700 until it returns to 150mm high at the cylinder so it is good but no magic bullet.
×
×
  • Create New...