Jump to content
SAU Community

Happy Laps - Queensland Raceway 07-12-14


Recommended Posts

Event:
Happy Laps - Queensland Raceway
Description:
A chance to get out on track for a fun cruise and have some om nom noms! Bit of spirited driving is allowed but it is still an event on a race track so a few rules need to be followed (see below). Also if you have not done QR before this is your ticket in to Lakeside.
Location:
Queensland Raceway
Date:
Sunday the 7th of December.
Time:
7:00 AM Arrival
Cost:
$35 for members and guests of members
$50 for non members
Please note that this is a per person cost, any passengers etc are required to pay as well.
Requirements:
1. QR have a minimum age of 12 for passengers.
2. No overtaking in the first 2 laps.
3. The overtaking car is responsible for completing the overtaking move safely.
4. Overtaking is only permitted on straights, unless clearly waved passed by the car in front.
5. Overtaking move must be completed well before the end of the straight, and the car being overtaken must be given plenty of room.
6. Cars should not be more than 2 abreast at any point on the track.
7. Be aware of cars around you, in front and behind (and beside when being overtaken).
8. Do not assume that the car in front of you knows you are there.
QR RULES

10. There is to be no racing

11. The straights are speed limited to 120km/h

12. Any car that goes off the track will be pulled off

13. There is not to be more than 1 sec of tyre smoke.

14. There are to be no helmets

15. Vehicles must have current registration and number plates are not to be obscured in anyway

Payment Details:

Name: Skylines Australia Queensland Club

Bank: Westpac

BSB: 034 063

ACC: 354012

PAYMENT REFERENCE: Username&HappyLaps

Attendees:
  1. Cadmoon +1
  2. gts032 +1
  3. Sho Pi
  4. sneaky pete
  5. AndrewK34
  6. pretX

will pay this week mike,cheers,hope theres more than just you and me out there smashing it,otherwise may have to change the club name to sometimes skylines australia,sometimes cant be stuffed.lol.

  • Like 1

be nice to catch up with you one more time this year on the track andrew,will see you at auto one this weekend anyway. :)

Yes, will catch up this week end, I will met you at the BP.

And yes all good for happy laps, coming home Saturday night, yippee.

  • 2 weeks later...

and then there were 5 keen skyline owners willing to take it to the evos that will be there as not enough members from sau can be stuffed to do the LAST SAU happy laps for the year.looks like most skylines are going from race breed,to shed kept. :(:(:(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...