Jump to content
SAU Community

Recommended Posts

Hi all just seeing what people's thoughts are and what may be the cause....

I got a rb25 neo with a gt3076r.82 and I'm not getting full boost until 5500rpm...feels way too laggy for me and from my research and what other people have said it shouldn't be so laggy either. I've just brought a .63 rear housing to get better response (not fitted yet) but I feel like it shouldn't be so laggy anyway and maybe there's an underlying issue?? Setups currently making 340kw @17psi.

Some of the Mods are:

New neo engine

Plazmaman plenum

1000cc injectors

Rb26 covers -12 breathers

52mm rad

600x300x100 fmic

One piece cooler pipping

Fpr

6boost top mount

Gt3076.82

Haltech platinum pro

Edited by lusunt
Link to comment
https://www.sau.com.au/forums/topic/454627-rb25-neo-gt3076-issue/
Share on other sites

Getting VCT working should be a priority, unless you don't have stock cams?
I believe it will give you about 200rpm more response compared to off.
I would be PM Stao from hypergear and see if he will give you some tips.

The .62 housing will prob get you about another 500 rpm response.
Is it running internal gate?
Try pre loading the actuator

Edit,

Oh yeh, a china spec 3076 will do this :P

Edit again

340 kw with a gt3076 and only 17 psi? That doesnt seem right?
are you on E85?

Edited by jay-rod

Getting VCT working should be a priority, unless you don't have stock cams?

I believe it will give you about 200rpm more response compared to off.

I would be PM Stao from hypergear and see if he will give you some tips.

The .62 housing will prob get you about another 500 rpm response.

Is it running internal gate?

Try pre loading the actuator

Edit,

Oh yeh, a china spec 3076 will do this :P

Edit again

340 kw with a gt3076 and only 17 psi? That doesnt seem right?

are you on E85?

Well my thoughts were that it should hit full boost at around 4000rpm 4400 at latest

if vct only effects it by a couple hundred rpm then I'm not fussed about using it...

Sorry it's

45mil turbosmart External gate

Genuine gt3076

and yeh e85

Edited by lusunt

Then dont use it, but if you have a neo engine with neo cams, why the hell wouldnt you?
No negatives, only positives???

But yes every 3076 i see has full boost by ~4300 on a rb25

Gate could be causing slow boost, do you have a dyno graph with correct scaling?
Would help out most people here diagnoses issues

Edited by jay-rod

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...